Author | Topic |
Location: Auckland, New Zealand
Registered: October 2002
|
Injector specifications. 7AFE, 7MGE
|
Sun, 27 April 2003 22:12
|
|
Does anyone know the specifications of the following injectors?
1997 7AFE (1.8L) injectors:
* impedence = ?
* what cc are these?
1988-92 7MGE non-turbo supra injectors:
* impedence = ?
* are these 320cc?
thanks!
|
|
|
Location: Sydney, OZ
Registered: May 2002
|
Re: Injector specifications. 7AFE, 7MGE
|
Sun, 27 April 2003 23:08
|
|
7AFE
95cc/min, 13.8 ohms.
7MGE
150cc/min, ??? ohms
|
|
|
Location: Auckland, New Zealand
Registered: October 2002
|
Re: Injector specifications. 7AFE, 7MGE
|
Sun, 27 April 2003 23:15
|
|
Forgive me for my ignorance, but is "cc" short for cubic centimeters? and in the context of injectors cubic centimeters per minute? Im assuming this would be at a given fuel pressure tho right? Say 36psi maybe?
I was informed that the 7MGE injectors were 320cc injectors? 4AGE red tops use about 200cc injectors right? I know that CD5A mitsi lancer GSR ones are 390cc and RB20DET ones are about 260-280cc perhaps we refer to them differently here in NZ? or are the 7AFE ones really that small!?!
(slightly confused).
|
|
|
I supported Toymods
Location: I renounced punctuation
Registered: May 2002
|
|
|
Location: Auckland, New Zealand
Registered: October 2002
|
Re: Injector specifications 7MGE
|
Mon, 28 April 2003 01:38
|
|
Wicked - thanks for that information. I think I will put that "injector testing" information to good use
|
|
|
Location: Lost in the K hole
Registered: May 2002
|
Re: Injector specifications. 7AFE, 7MGE
|
Mon, 28 April 2003 03:11
|
|
watch out though...
86-87 7mge's run low impedance 3.x ohm (yellow) injectors...
88-91 7mge's run high impedance 13.8 ohm (?colour?) injectors...
both flow ~285cc/min (where'd you get that 150 figure from??)
flow rates for the two are basically the same, though they are specified different - but at different test pressures.
|
|
|
I supported Toymods
Location: I renounced punctuation
Registered: May 2002
|
Re: Injector specifications. 7AFE, 7MGE
|
Mon, 28 April 2003 03:53
|
|
Either way, easy enough to measure the resistance.
|
|
|
Location: Sydney, OZ
Registered: May 2002
|
Re: Injector specifications. 7AFE, 7MGE
|
Tue, 29 April 2003 00:57
|
|
Quote: | both flow ~285cc/min (where'd you get that 150 figure from??)
|
The last engine I built, I did some investigation work, I lined up the following list, and had them clean and flowed on a professional flow bench (Vane Autocraft Injector flow bench), all figures are at 300Kpa (44Psi), so naturally more pressure more flow in theory:
22RE- 92cc/min
4AGE 100Kw- 95cc/min
7AFE -94.4cc/min
7MGE - 150cc/min
4AGZE- 200cc/min
The 7M I have are green and are 13.8 ohm's... I checked them last night. the 7AFTE that was available here had a were purple, but I wouldn't know the flow rates.
|
|
|