| Author | Topic |
|---|
Location:
Red Deer Alberta Canada
Registered:
December 2003
|
|
20 valve black top ae86
|
Fri, 26 December 2003 16:45
|
 |
i am in the midts of this conversion into my ae86 and could really use a wireing diagram for the ae111 black top .
can anyone here help?
|
|
|
Location:
Wollongong
Registered:
November 2002
|
|
|
Location:
Richmond NSW
Registered:
September 2003
|
|
|
Location:
Red Deer Alberta Canada
Registered:
December 2003
|
|
Re: 20 valve black top ae86
|
Sat, 27 December 2003 06:37
|
|
Thank you verry much Matt ... got any pics of your swap ? send them to my email at chrisandlisa@shaw.ca
i may need your help further down my swap if i could call upon your wisdom later . atleast email me your email .
|
|
|
Location:
Red Deer Alberta Canada
Registered:
December 2003
|
|
Re: 20 valve black top ae86
|
Sun, 28 December 2003 17:57
|
|
I still ned a verry good wireing scematic of the ae111 black top 20 v
thoes links are verry helpfull but i need the factory diagram from the repair manuals ...anyone?
|
|
|
Location:
NSW, East Coast
Registered:
July 2003
|
|
Re: 20 valve black top ae86
|
Mon, 29 December 2003 01:11
|
|
You may need to talk to Toyota and get them to get you the info you need, or ask some of your local importers if they can help, surely someone will help you?
Steve
|
|
|
Location:
Red Deer Alberta Canada
Registered:
December 2003
|
|
Re: 20 valve black top ae86
|
Sat, 03 January 2004 17:18
|
|
|
a guy from the phillapens sent me a complete south african manual .
|
|
|
Location:
qld
Registered:
December 2003
|
|
Re: 20 valve black top ae86
|
Mon, 05 January 2004 03:41
|
|
|
tried club4ag.com?
|
|
|
Location:
sydney
Registered:
March 2004
|
|
Re: 20 valve black top ae86
|
Fri, 12 March 2004 12:21
|
|
|
i am doing this at the moment as well i found the whole black top engine manual on the net i'm pretty sure it has it in there. how does yours look
|
|
|
Location:
Brisbane
Registered:
May 2002
|
|
Re: 20 valve black top ae86
|
Fri, 12 March 2004 13:03
|
|
the blacktop loom isn't all that hard once you strip out all the un-necessary stuff, you are left with basically JUST the engine loom from the blacktop after all the other garbage is removed, and then you simply splice this into your existing body/ignition/charge looms. Took me about 3 nights after work to do, but I checked every wire in the loom... The thing fired first go with all the instrumentation etc working perfectly.
The padandwheels site is very good, there's only a couple of mistakes there in his pinouts which are pretty obvious when you check your loom with the multimeter.
Mine went from a mess like this:
http://www.rollamods.com/project20V/wiring2.jpg
To a much neater "plug and play" harness like this:
http://www.rollamods.com/project20V/wiring3.jpg
The extra wires in the pic near the ECU were integrated into the F2 plug for the body harness, it turned out extremely neat in the end, just like factory.
|
|
|
which sucked but i found this site which is half use full ok it explains each plug and stuff. (get it done buy the guy who advertise on the website i think sideshow its easiest that way less headache)