| Author | Topic |
|---|
I supported Toymods
Location:
I renounced punctuation
Registered:
May 2002
|
|
Re: Tech Info on the 5M-E (MA61)
|
Fri, 21 June 2002 03:53
 
|
 |
Allan, with the correct tool and some care, valve stem seal replacement can be done without taking the head off, as I told you before you did yours!  Most people decide it's a good excuse to redo the head gasket. I have done it a couple of times on old 4M's with no probs.
Simply turn engine to TDC for that cylinder, using a top acting valve spring compressor, remove the collets that hold the retainer in place and remove the lot. This leaves the valve and stem seal in clear view. Remove and replace. Reverse above process. Retorque head, set valve clearances, and you're away. Retorque head and redo valve clearances at 1000 km. You MUST be careful to not disturb the head whilst doing this.
|
|
|
| | Subject | Poster | Date |
|---|
 |
Tech Info on the 5M-E (MA61)
|
ZZT231 | Tue, 04 June 2002 09:33 |
|
Re: Tech Info on the 5M-E (MA61)
|
Allan | Tue, 04 June 2002 09:37 |
|
Re: Tech Info on the 5M-E (MA61)
|
ed_ma61 | Tue, 04 June 2002 10:02 |
|
Re: Tech Info on the 5M-E (MA61)
|
ZZT231 | Tue, 04 June 2002 10:12 |
|
Re: Tech Info on the 5M-E (MA61)
|
ed_ma61 | Tue, 04 June 2002 10:28 |
|
Re: Tech Info on the 5M-E (MA61)
|
ZZT231 | Tue, 04 June 2002 10:43 |
|
Re: Tech Info on the 5M-E (MA61)
|
ZZT231 | Tue, 04 June 2002 10:49 |
|
Re: Tech Info on the 5M-E (MA61)
|
ZZT231 | Tue, 04 June 2002 11:06 |
|
Re: Tech Info on the 5M-E (MA61)
|
justcallmefrank | Tue, 04 June 2002 10:41 |
|
Re: Tech Info on the 5M-E (MA61)
|
justcallmefrank | Tue, 04 June 2002 10:43 |
|
Re: Tech Info on the 5M-E (MA61)
|
justcallmefrank | Tue, 04 June 2002 10:50 |
|
Re: Tech Info on the 5M-E (MA61)
|
suprav8 | Tue, 04 June 2002 11:19 |
|
Re: Tech Info on the 5M-E (MA61)
|
Norbie | Tue, 04 June 2002 11:29 |
|
Re: Tech Info on the 5M-E (MA61)
|
ed_ma61 | Tue, 04 June 2002 12:53 |
|
Re: Tech Info on the 5M-E (MA61)
|
ed_ma61 | Tue, 04 June 2002 12:59 |
|
Re: Tech Info on the 5M-E (MA61)
|
gianttomato | Tue, 04 June 2002 13:16 |
|
Re: Tech Info on the 5M-E (MA61)
|
Allan | Fri, 21 June 2002 03:22 |
|
Re: Tech Info on the 5M-E (MA61)
|
gianttomato | Fri, 21 June 2002 03:53 |
|
Re: Tech Info on the 5M-E (MA61)
|
Allan | Fri, 21 June 2002 05:54 |
|
Re: Tech Info on the 5M-E (MA61)
|
justcallmefrank | Tue, 04 June 2002 13:14 |
|
Re: Tech Info on the 5M-E (MA61)
|
bunny | Tue, 04 June 2002 13:22 |
|
Re: Tech Info on the 5M-E (MA61)
|
bunny | Tue, 04 June 2002 14:05 |
|
Re: Tech Info on the 5M-E (MA61)
|
kevz0r | Wed, 05 June 2002 01:41 |
|
Re: Tech Info on the 5M-E (MA61)
|
kevz0r | Wed, 05 June 2002 01:44 |
|
Re: Tech Info on the 5M-E (MA61)
|
Stefan | Sun, 23 June 2002 01:11 |
|
Re: Tech Info on the 5M-E (MA61)
|
Stefan | Sun, 23 June 2002 01:13 |
|
Re: Tech Info on the 5M-E (MA61)
|
ma61_turbo | Fri, 21 June 2002 02:58 |
|
Re: Tech Info on the 5M-E (MA61)
|
Norbie | Sun, 23 June 2002 07:04 |
|
Re: Tech Info on the 5M-E (MA61)
|
manipulate | Sun, 23 June 2002 07:25 |
|
Re: Tech Info on the 5M-E (MA61)
|
Stefan | Sun, 23 June 2002 07:31 |
|
Re: Tech Info on the 5M-E (MA61)
|
justcallmefrank | Sun, 23 June 2002 10:15 |
|
Re: Tech Info on the 5M-E (MA61)
|
manipulate | Sun, 23 June 2002 10:52 |
|
Re: Tech Info on the 5M-E (MA61)
|
justcallmefrank | Sun, 23 June 2002 11:02 |
|
Re: Tech Info on the 5M-E (MA61)
|
manipulate | Sun, 23 June 2002 11:21 |
|
Re: Tech Info on the 5M-E (MA61)
|
Stefan | Sun, 23 June 2002 12:11 |
|
Re: Tech Info on the 5M-E (MA61)
|
Stefan | Sun, 23 June 2002 12:13 |
|
Re: Tech Info on the 5M-E (MA61)
|
justcallmefrank | Sun, 23 June 2002 12:13 |
|
Re: Tech Info on the 5M-E (MA61)
|
Stefan | Sun, 23 June 2002 12:18 |
|
Re: Tech Info on the 5M-E (MA61)
|
justcallmefrank | Sun, 23 June 2002 12:29 |
|
Re: Tech Info on the 5M-E (MA61)
|
Stefan | Sun, 23 June 2002 12:36 |
| Current Time:
Fri Nov 15 23:55:55 UTC 2024 |
Total time taken to generate the page: 0.0086050033569336 seconds |
