Toymods Car Club
www.toymods.org.au
F.A.Q. F.A.Q.    Register Register    Login Login    Home Home
Members Members    Search Search
Toymods » Tech & Conversions » [Tech] Walbro install into Supra info here.

Show: Today's Posts  :: Show Polls 
Email to friend 
Return to the default flat view Create a new topic Submit Reply
AuthorTopic
wastegate
Regular


Location:
Gold Coast
Registered:
May 2002
 
[Tech] Walbro install into Supra info here. Sun, 14 September 2003 11:58 Go to previous message
Well thanks to 7M-Brisbane and Norbie for giving a hand, I installed a Walbro pump yesterday, thought I would document it incase any other Supra owner wants to do the same.

http://www.jzgte.com/~nickc/albums/Walbro/DSC00006.thumb.jpg
First unscrew the 4 screws holding the cover of the fuel filler on and take it out.

http://www.jzgte.com/~nickc/albums/Walbro/DSC00008.thumb.jpg
Jack the car up under the diff and put jack stands under the car as you will need the jack to help support the fuel tank.

http://www.jzgte.com/~nickc/albums/Walbro/DSC00009.thumb.jpg
Unbolt the plastic shroud cover at the front of the fuel tank. There are 4 bolts to undo. It's can be alittle tricky to get out.

http://www.jzgte.com/~nickc/albums/Walbro/DSC00011.thumb.jpg
Here is the cover undone.

http://www.jzgte.com/~nickc/albums/Walbro/DSC00012.thumb.jpg
You will need to undo these lines to get the tank out. One of the clamp hoses is the breather and the other the fuel return line. The bolted section is the high pressure line. You will need a 19mm and a 14mm to undo this. The 19mm section is the one that undoes. Watch for fuel spillage here as there will be abit if the line is still under pressure.

http://www.jzgte.com/~nickc/albums/Walbro/DSC00013.thumb.jpg
Here are the two bolts that hold the fuel tank up. Undo these bolts but not off. Only loosen them off abit.

http://www.jzgte.com/~nickc/albums/Walbro/DSC00016.thumb.jpg
Unplug the fuel level sender sensor wires from within the boot.

http://www.jzgte.com/~nickc/albums/Walbro/DSC00017.thumb.jpg
Now with the jack and a peice of wood/books to spred the weight onto the jack, put it under the tank between the two straps. Now jack it up alittle to give the belts some slack. Take out the pins for the belts and undo the bolts to remove the belts.

http://www.jzgte.com/~nickc/albums/Walbro/DSC00018.thumb.jpg
Reach up and disconnect the fuel pump connector from the car.

http://www.jzgte.com/~nickc/albums/Walbro/DSC00020.thumb.jpg
With abit of loweringof the jack the tank should be able to be lowered out, make sure that the tank comes to the passinger/left side of the car while it's lowering to get the filler out.
  Send a private message to this user    

SubjectPosterDate
Read Message   [Tech] Walbro install into Supra info here.  wastegateSun, 14 September 2003 11:58
Read Message   Re: [Tech] Walbro install into Supra info here. wastegateSun, 14 September 2003 11:58
Read Message   Re: [Tech] Walbro install into Supra info here. Sun, 14 September 2003 12:19
Read Message   Re: [Tech] Walbro install into Supra info here. wastegateSun, 14 September 2003 12:25
Read Message   Re: [Tech] Walbro install into Supra info here. Sun, 14 September 2003 12:29
Read Message   Re: [Tech] Walbro install into Supra info here. crazy_camrySun, 14 September 2003 12:30
Read Message   Re: [Tech] Walbro install into Supra info here. Sun, 14 September 2003 12:33
Read Message   Re: [Tech] Walbro install into Supra info here. crazy_camrySun, 14 September 2003 12:36
Read Message   Re: [Tech] Walbro install into Supra info here. NorbieSun, 14 September 2003 12:43
Read Message   Re: [Tech] Walbro install into Supra info here. crazy_camrySun, 14 September 2003 12:53
Previous Topic:Head swap necessary......
Next Topic:Extractors

Goto Forum:
-=] Back to Top [=-

Current Time: Mon Dec 23 15:58:59 UTC 2024

Total time taken to generate the page: 0.0063529014587402 seconds

Bandwidth utilization bar

.:: Contact :: Home ::.

Powered by: FUDforum 2.3.8
Copyright ©2001-2003 Advanced Internet Designs Inc.