F.A.Q.    Register    Login    Home Members    Search

Toymods » Tech & Conversions » 4AGE into a 4AFE Show: Today's Posts  :: Show Polls  Email to friend

Author	Topic
Bill Sherwood Forums Junkie Location: Brisbane / Gold Coast Registered: May 2002	Re: 4AGE into a 4AFE Fri, 28 November 2003 12:10 Reasons for - - 31mm buckets, so big cams aren't a problem at all. - Narrower valve angle, 22.5°. - MUCH better inlet port. Reasons against - - Squish areas are located in four areas Vs the G head's two large ones. I haven't measured them as such but I'd say the F head has about the same total area anyway though. So with work they're probably just as good but it's more work to get right. - Hard to alter the lobe centres WRT each other unless you build a very small slotted drive gear between the cams. - The exhaust ports also need a lot of work to get right. Cyls #2 & #3 are not too bad, but #1 & #4 are angled and need more work than the middle two. I plan on using ovaled ports, this'll make the job of making all the ports the same much easier. - People think you're barking mad! [Report message to a moderator]

	Subject	Poster	Date
	4AGE into a 4AFE	SecaBoy	Thu, 27 November 2003 00:30
	Re: 4AGE into a 4AFE	STR8 2.8	Fri, 28 November 2003 05:57
	Re: 4AGE into a 4AFE	SecaBoy	Sun, 30 November 2003 21:48
	Re: 4AGE into a 4AFE	Bill Sherwood	Fri, 28 November 2003 06:21
	Re: 4AGE into a 4AFE	IRA11Y	Fri, 28 November 2003 06:26
	Re: 4AGE into a 4AFE	Bill Sherwood	Fri, 28 November 2003 12:10
	Re: 4AGE into a 4AFE	IRA11Y	Fri, 28 November 2003 23:11
	Re: 4AGE into a 4AFE	Classique71	Sat, 29 November 2003 01:20
	Re: 4AGE into a 4AFE	Bill Sherwood	Sat, 29 November 2003 04:51
	Re: 4AGE into a 4AFE	IRA11Y	Sat, 29 November 2003 05:22
	Re: 4AGE into a 4AFE	Chris Davey	Sat, 29 November 2003 05:28
	Re: 4AGE into a 4AFE	Johnny	Sun, 30 November 2003 01:33
	Re: 4AGE into a 4AFE	Bill Sherwood	Mon, 01 December 2003 01:53
	Re: 4AGE into a 4AFE	Johnny	Mon, 01 December 2003 02:40
	Re: 4AGE into a 4AFE	IRA11Y	Mon, 01 December 2003 05:35
	Re: 4AGE into a 4AFE	Johnny	Tue, 02 December 2003 05:09
	Re: 4AGE into a 4AFE	Bill Sherwood	Wed, 03 December 2003 18:23
	Re: 4AGE into a 4AFE	Grega	Wed, 03 December 2003 22:11
	Re: 4AGE into a 4AFE	IRA11Y	Thu, 04 December 2003 03:38

Previous Topic:	Looking at buying ST205 - inspection.
Next Topic:	weight of 1g-gte

Powered by: FUDforum 2.3.8
Copyright ©2001-2003 Advanced Internet Designs Inc.