| Author | Topic |
|---|
Location:
townsville NQLD
Registered:
February 2004
|
|
Re: celica steering box compatability (pre 81')
|
Wed, 11 August 2004 04:09
 
|
 |
hi all,
this is a old topic i wrote a while ago, it seemed nobody was interested in ra40 conversions. should explain most. ive completed this conversion and it works great, the only problem i had was the pump leaked - jus needs a new seal.
hi guys
i have found that many cressida parts will fit onto my ra40. firstly power steering, the bolt holes all line up perfectly, so no new holes will need to be drilled or modified. the only problem i encountered is that the 2 pin rubber disc plate that connects to the steerin column shaft sits about 15 - 20 mm to far up. this can be corected by sliding the 2 pin rubber disc plate down on the steering box spline as far as it will go, then tightening the bolt which holds it there. this only leaves it out by about 7mm. to get this extra 7mm the steering shaft will need to be machined at the the top end so the ignition switch and bearing can be slid back into its origional position. brackets for the pump will need to be fabricated.
power locking will literally bolt in, but conecting rods will need to be made to join the locking mechanism with the electromagnet.
power windows are a bit of a challange as the winder frames are different between cressidas and celicas. i cut both winder frames at the same position and the welded the bottom part (cressida - where electric motor bolts on) to the top part (celica winder frame)- this combination seems to work fine. 2 existing holes can be used but 2 new hole will need to be drilled. spacers need to be used on all holes because the electric motor sits out furthur than what the celica winder frame does.
many other parts are interchangable like, throttle cable, elec. ignition igniter assist, radiator, center console and much more
i hoped this article can help someone.
brett
|
|
|
| | Subject | Poster | Date |
|---|
 |
celica steering box compatability (pre 81') - (now has diagram for p/s conversion) check it out
|
brett_celicacoupe | Wed, 11 August 2004 03:19 |
|
Re: celica steering box compatability (pre 81')
|
thechuckster | Wed, 11 August 2004 03:36 |
|
Re: celica steering box compatability (pre 81')
|
ozboy | Wed, 11 August 2004 03:50 |
|
Re: celica steering box compatability (pre 81')
|
brett_celicacoupe | Wed, 11 August 2004 04:09 |
|
Re: celica steering box compatability (pre 81')
|
CrAiGzEE | Wed, 11 August 2004 06:32 |
|
Re: celica steering box compatability (pre 81')
|
THE WITZL | Wed, 11 August 2004 08:04 |
|
Re: celica steering box compatability (pre 81')
|
brett_celicacoupe | Wed, 11 August 2004 10:22 |
|
Re: celica steering box compatability (pre 81')
|
brett_celicacoupe | Wed, 11 August 2004 10:38 |
|
Re: celica steering box compatability (pre 81')
|
thechuckster | Wed, 11 August 2004 13:31 |
|
Re: celica steering box compatability (pre 81')
|
CrAiGzEE | Thu, 12 August 2004 00:25 |
|
Re: celica steering box compatability (pre 81')
|
CrAiGzEE | Thu, 12 August 2004 00:31 |
|
Re: celica steering box compatability (pre 81')
|
chrishulbert | Thu, 12 August 2004 00:36 |
|
Re: celica steering box compatability (pre 81')
|
CrAiGzEE | Thu, 12 August 2004 01:15 |
|
Re: celica steering box compatability (pre 81')
|
chrishulbert | Thu, 12 August 2004 02:04 |
|
Re: celica steering box compatability (pre 81')
|
CrAiGzEE | Thu, 12 August 2004 02:08 |
|
Re: celica steering box compatability (pre 81')
|
chrishulbert | Thu, 12 August 2004 02:26 |
|
Re: celica steering box compatability (pre 81') - (now has diagram for p/s conversion) check it out
|
crazedrt104 | Wed, 11 August 2004 22:48 |
|
Re: celica steering box compatability (pre 81') - (now has diagram for p/s conversion) check it out
|
TurboRA28 | Wed, 11 August 2004 23:08 |
|
Re: celica steering box compatability (pre 81') - (now has diagram for p/s conversion) check it out
|
brett_celicacoupe | Thu, 12 August 2004 03:51 |
|
Re: celica steering box compatability (pre 81') - (now has diagram for p/s conversion) check it out
|
7M-Brisbane | Sun, 29 August 2004 13:07 |
