| Author | Topic |
|---|
Location:
Terrigal
Registered:
May 2002
|
|
Re: Installing Camber tops
|
Thu, 16 September 2004 04:17
 
|
 |
As for Noltec.. they seem to be made well but I also had to file out the holes a few mm same as you ke382tg. But dont think it was quite 7mm.
What I don't like about them is the lack of adjustment, the design which I think is similar to kmac, is you have a large plate sandwitched between 2 other plates. Now if you try to dial in a lot of neg the plate just hits the inside of the shock tower. Most I can get is around 1.5 neg, now with my RCA's in place, I have basically neutral camber with the strut tops dialed right in.
When I originally ordered them Noltec had 2 types, one 'supposedly' went up to around 3 deg neg camber which I thought would be heaps. The other was for up to neg 6, but these are a lot harsher as no rubber in them. If I was to purchase another set i'd get these though.
T3 design and cusco looks a lot better, but they dont make them for RA celicas, just AE86's.
Im going to be moving my control arms out 20mm to get some neg camber then just use the strut tops to fine tune it.
Cheers
Joel
|
|
|
| | Subject | Poster | Date |
|---|
 |
Installing Camber tops
|
papercut | Thu, 16 September 2004 02:03 |
|
Re: Installing Camber tops
|
TurboRA28 | Thu, 16 September 2004 02:13 |
|
Re: Installing Camber tops
|
blackRA28 | Thu, 16 September 2004 02:53 |
|
Re: Installing Camber tops
|
papercut | Thu, 16 September 2004 03:20 |
|
Re: Installing Camber tops
|
ke382TG | Thu, 16 September 2004 03:46 |
|
Re: Installing Camber tops
|
TurboRA28 | Thu, 16 September 2004 04:17 |
|
Re: Installing Camber tops
|
papercut | Thu, 16 September 2004 05:02 |
|
Re: Installing Camber tops
|
TurboRA28 | Thu, 16 September 2004 05:39 |
|
Re: Installing Camber tops
|
ke382TG | Thu, 16 September 2004 05:45 |
|
Re: Installing Camber tops
|
TurboRA28 | Thu, 16 September 2004 06:11 |
|
Re: Installing Camber tops
|
ke382TG | Thu, 16 September 2004 06:16 |
|
Re: Installing Camber tops
|
TurboRA28 | Thu, 16 September 2004 06:22 |
|
Re: Installing Camber tops
|
papercut | Thu, 16 September 2004 06:50 |
|
Re: Installing Camber tops
|
TurboRA28 | Thu, 16 September 2004 07:04 |
|
Re: Installing Camber tops
|
blackRA28 | Thu, 16 September 2004 11:29 |
|
Re: Installing Camber tops
|
TurboRA28 | Thu, 16 September 2004 23:34 |
|
Re: Installing Camber tops
|
takai | Thu, 16 September 2004 14:46 |
|
Re: Installing Camber tops
|
ae95 | Thu, 16 September 2004 16:20 |
|
Re: Installing Camber tops
|
takai | Thu, 16 September 2004 22:05 |
|
Re: Installing Camber tops
|
datman55 | Fri, 08 October 2004 05:26 |
