| Author | Topic |
|---|
I supported Toymods
Location:
Australia
Registered:
November 2003
|
|
Re: high tensile wheel studs
|
Fri, 18 February 2005 01:30
 
|
 |
| Quote: |
| CrUZsida wrote on Mon, 22 November 2004 22:38 |
Ok, using the Nice Products catalogue (http://www.niceproducts.com.au) this is what I have found
S340 - Most RWD Toyota (including MX73 and MA61)
listed as 40mm long (could not find on webpage, but am remembering from looking at catalogue)
S310 - Lots of cars, including 80 series landcruisers
listed as 40.1mm long
S312 - LN36/RN105/YN60-67 Hilux, Most Drum Landcruisers (40-50-60-70 series), Most Magna's
listed as 45.2mm long
S314 - Pajero Front
listed as 40mm long
S315 - Pajero Rear, Jackaroo
listed as 42.4mm long
Now, I think the S340 is a typo, and it should be 35mm long (or there abouts) but I didn't remember to recheck it.
The VY commie ones weren't on the webpage either.
|
Ok, I check the catalogue, and my MA61/MX73 wheel stud.
S340 - Most RWD pre 1990's Toyota's.
Knurl = 14.3mm
Length = 40mm
Shoulder = 8mm
That length SHOULD be 36mm.
I have measured an Aus delivered MX73, and a Malaysian MA61, both identical.
S381 - VX II, VY, VZ
Knurl = 14.3mm
Length = 48.4mm
Shoulder = 8mm
So, the best bets are.
S310 ~ 4mm increase in stud length
S314 ~ 4mm increase in stud length
S315 ~ 6mm increase in stud length
S312 ~ 9mm increase in stud length
S381 ~ 12mm increase in stud length
All are made by NiceProducts, and retail around $5 each.
|
|
|
|
| | Subject | Poster | Date |
|---|
 |
high tensile wheel studs
|
draven | Thu, 17 February 2005 11:29 |
|
Re: high tensile wheel studs
|
Allan | Thu, 17 February 2005 12:09 |
|
Re: high tensile wheel studs
|
shinybluesteel | Thu, 17 February 2005 12:32 |
|
Re: high tensile wheel studs
|
draven | Thu, 17 February 2005 13:55 |
|
Re: high tensile wheel studs
|
bbaacchhyy | Thu, 17 February 2005 20:45 |
|
Re: high tensile wheel studs
|
draven | Thu, 17 February 2005 23:40 |
|
Re: high tensile wheel studs
|
bbaacchhyy | Thu, 17 February 2005 23:51 |
|
Re: high tensile wheel studs
|
draven | Fri, 18 February 2005 00:06 |
|
Re: high tensile wheel studs
|
bbaacchhyy | Fri, 18 February 2005 01:02 |
|
Re: high tensile wheel studs
|
takai | Thu, 17 February 2005 13:03 |
|
Re: high tensile wheel studs
|
justcallmefrank | Fri, 18 February 2005 00:14 |
|
Re: high tensile wheel studs
|
draven | Fri, 18 February 2005 01:08 |
|
Re: high tensile wheel studs
|
justcallmefrank | Fri, 18 February 2005 01:10 |
|
Re: high tensile wheel studs
|
bbaacchhyy | Fri, 18 February 2005 01:17 |
|
Re: high tensile wheel studs
|
justcallmefrank | Fri, 18 February 2005 01:20 |
|
Re: high tensile wheel studs
|
draven | Fri, 18 February 2005 01:14 |
|
Re: high tensile wheel studs
|
justcallmefrank | Fri, 18 February 2005 01:15 |
|
Re: high tensile wheel studs
|
draven | Fri, 18 February 2005 01:21 |
|
Re: high tensile wheel studs
|
justcallmefrank | Fri, 18 February 2005 01:25 |
|
Re: high tensile wheel studs
|
bbaacchhyy | Fri, 18 February 2005 01:25 |
|
Re: high tensile wheel studs
|
justcallmefrank | Fri, 18 February 2005 01:23 |
|
Re: high tensile wheel studs
|
draven | Fri, 18 February 2005 01:27 |
|
Re: high tensile wheel studs
|
CrUZsida | Fri, 18 February 2005 01:30 |
|
Re: high tensile wheel studs
|
bbaacchhyy | Fri, 18 February 2005 01:50 |
|
Re: high tensile wheel studs
|
CrUZsida | Fri, 18 February 2005 01:57 |
|
Re: high tensile wheel studs
|
bbaacchhyy | Fri, 18 February 2005 02:01 |
|
Re: high tensile wheel studs
|
CrUZsida | Fri, 18 February 2005 02:08 |
|
Re: high tensile wheel studs
|
bbaacchhyy | Fri, 18 February 2005 02:15 |
|
Re: high tensile wheel studs
|
CrUZsida | Fri, 18 February 2005 02:17 |
