F.A.Q.    Register    Login    Home Members    Search

Toymods » Tech & Conversions » Wiring loom problems (3TGTE) Show: Today's Posts  :: Show Polls  Email to friend

Author	Topic
roger Regular Registered: June 2002	Re: Wiring loom problems (3TGTE) Wed, 12 February 2003 01:08 If you have 1.7 ohm injectors you must use the ballast resistors with this system. Standard 3tgteu injectors are 12 Ohms, if you havent already blown the injector drivers in the ecu you must do this before you attempt anything else. You should however still be able to check the pulse for the #10 and #20 out puts but do so with all injector disconnected from the loom. If you can't get this pulse there is something wrong with the injectors or the wirring. when checking the pulse you should do so with a logic probe, but not the crappy one you buy for $2 you should be using one with a led a pull down resistor of about 1K when logic probing an ecu. Use the $2 job with a probe can lead to damage to the ECU. Also when ever wiring relays make sure the power comes directly from the battery ( you seem to have power comming from the ignition switch this should be from the battery), and the switching is done through a signal such as the ignition signal This may be your problem but make sure of the injector resistance and use ballast resistors if necessary. Roger [Updated on: Wed, 12 February 2003 01:19] [Report message to a moderator]

	Subject	Poster	Date
	Wiring loom problems (3TGTE)	inferno	Fri, 07 February 2003 00:43
	Re: Wiring loom problems (3TGTE)	roger	Fri, 07 February 2003 01:00
	Re: Wiring loom problems (3TGTE)	Norbie	Fri, 07 February 2003 01:07
	Re: Wiring loom problems (3TGTE)	inferno	Sat, 08 February 2003 22:40
	Re: Wiring loom problems (3TGTE)	CLG	Sun, 09 February 2003 04:13
	Re: Wiring loom problems (3TGTE)	inferno	Sun, 09 February 2003 05:05
	Re: Wiring loom problems (3TGTE)	CLG	Sun, 09 February 2003 09:56
	Re: Wiring loom problems (3TGTE)	Grant	Sun, 09 February 2003 21:27
	Re: Wiring loom problems (3TGTE)	inferno	Mon, 10 February 2003 22:32
	Re: Wiring loom problems (3TGTE)	inferno	Tue, 11 February 2003 05:53
	Re: Wiring loom problems (3TGTE)	roger	Wed, 12 February 2003 00:18
	Re: Wiring loom problems (3TGTE)	inferno	Wed, 12 February 2003 00:37
	Re: Wiring loom problems (3TGTE)	roger	Wed, 12 February 2003 01:08
	Re: Wiring loom problems (3TGTE)	inferno	Tue, 18 February 2003 08:04
	Re: Wiring loom problems (3TGTE)	clubagreenie	Tue, 18 February 2003 08:31
	Re: Wiring loom problems (3TGTE)	inferno	Wed, 19 February 2003 13:42
	Re: Wiring loom problems (3TGTE)	roger	Wed, 19 February 2003 22:05
	Re: Wiring loom problems (3TGTE)	roger	Wed, 19 February 2003 22:12
	Re: Wiring loom problems (3TGTE)	TurboRA28	Wed, 19 February 2003 22:49
	Re: Wiring loom problems (3TGTE)	inferno	Thu, 20 February 2003 00:18
	Re: Wiring loom problems (3TGTE)	roger	Thu, 20 February 2003 02:39
	Re: Wiring loom problems (3TGTE)	TurboRA28	Thu, 20 February 2003 03:19
	Re: Wiring loom problems (3TGTE)	roger	Thu, 20 February 2003 03:31
	Re: Wiring loom problems (3TGTE)	inferno	Thu, 20 February 2003 04:13
	Re: Wiring loom problems (3TGTE)	roger	Thu, 20 February 2003 04:51
	Re: Wiring loom problems (3TGTE)	TurboRA28	Thu, 20 February 2003 05:41
	Re: Wiring loom problems (3TGTE)	inferno	Thu, 20 February 2003 08:09
	Re: Wiring loom problems (3TGTE)	roger	Thu, 20 February 2003 21:33
	Re: Wiring loom problems (3TGTE)	TurboRA28	Thu, 20 February 2003 22:06
	Re: Wiring loom problems (3TGTE)	inferno	Thu, 20 February 2003 23:11
	Re: Wiring loom problems (3TGTE)	roger	Thu, 20 February 2003 23:35
	Re: Wiring loom problems (3TGTE)	CLG	Fri, 21 February 2003 04:46
	Re: Wiring loom problems (3TGTE)	inferno	Fri, 21 February 2003 14:02
	Re: Wiring loom problems (3TGTE)	AE25	Wed, 04 May 2005 09:22

Previous Topic:	Greddy Profec B Spec II Tuners in Canberra
Next Topic:	2tg piston hits valve after hibread makeover

Powered by: FUDforum 2.3.8
Copyright ©2001-2003 Advanced Internet Designs Inc.