| Author | Topic |
|---|
I supported Toymods
Location:
I renounced punctuation
Registered:
May 2002
|
|
Re: Wiring 2jzge into 260z
|
Wed, 02 November 2005 08:00
 
|
 |
If you are prepared to wait till the weekend I can give you the diameter and thread of both.
As for speedo, just put a mechanical drive into your W58 gearbox - you'll need to pull the extension housing off to do this. Get a speedo cable made to go to your 260Z speedo with the Toyota connection at the gearbox end and a Datto connection at the speedo end (I am making the assumption that the 260Z uses a speedo cable). When you are up and running, take the car to a dyno and get them to do some speedo calibration runs. Take speedo and data fronm dyno to said instrument shop and get it recalibrated. This is a shitload cheaper than buying a range of aftermarket gauges and you'll retain the original look of the car.
I will get a photo of what I did for the oil pressure sender on my 2JZGE. This is uber easy and will cost you almost nothing.
|
|
|
| | Subject | Poster | Date |
|---|
 |
Wiring 2jzge into 260z
|
aussie260z | Thu, 21 July 2005 02:24 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Thu, 21 July 2005 04:09 |
|
Re: Wiring 2jzge into 260z
|
Henn | Thu, 21 July 2005 05:39 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Thu, 21 July 2005 05:41 |
|
Re: Wiring 2jzge into 260z
|
Henn | Thu, 21 July 2005 06:48 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Sat, 29 October 2005 06:50 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Sat, 29 October 2005 07:07 |
|
Re: Wiring 2jzge into 260z
|
brett_celicacoupe | Sat, 29 October 2005 07:33 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Sat, 29 October 2005 23:41 |
|
Re: Wiring 2jzge into 260z
|
Manny | Sun, 30 October 2005 01:08 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Mon, 31 October 2005 04:58 |
|
Re: Wiring 2jzge into 260z
|
Manny | Mon, 31 October 2005 05:36 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Mon, 31 October 2005 07:34 |
|
Re: Wiring 2jzge into 260z
|
Alchemist | Mon, 31 October 2005 10:10 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Tue, 01 November 2005 04:59 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Tue, 01 November 2005 05:26 |
|
Re: Wiring 2jzge into 260z
|
sideshow | Tue, 01 November 2005 07:00 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Tue, 01 November 2005 22:38 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Wed, 02 November 2005 08:00 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Wed, 02 November 2005 22:01 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Fri, 04 November 2005 22:22 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Fri, 04 November 2005 23:04 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Fri, 04 November 2005 23:41 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Sat, 05 November 2005 02:31 |
|
Re: Wiring 2jzge into 260z
|
wilbo666 | Sat, 05 November 2005 03:12 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Sat, 05 November 2005 03:33 |
|
Re: Wiring 2jzge into 260z
|
wilbo666 | Sat, 05 November 2005 04:24 |
|
Re: Wiring 2jzge into 260z
|
Norbie | Fri, 11 November 2005 00:10 |
|
Re: Wiring 2jzge into 260z
|
mrshin | Sun, 06 November 2005 08:59 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Thu, 10 November 2005 23:46 |
