| Author | Topic |
|---|
Location:
Brisbane
Registered:
May 2002
|
|
Re: Wiring 2jzge into 260z
|
Sat, 05 November 2005 03:12
 
|
 |
| gianttomato wrote on Sat, 05 November 2005 10:41 |
As for the shifter position, yes you can change it but you will need to modify the shifter the tiniest bit. Norbie did this when he fitted the W58 to his 2JZGTE. He might even be able to supply you the required bits seeing as he killed his W58....
See here.
|
You only have to modify the shift linkage (the modification is done to the shift linkage rod) if you are using the JZA80 shift rod the bolt hole to mount the shift linkage elbow is different. Get the normal rod from a steel plate gearbox and it should be fine. The alloy sandwich plate and steel plate boxes have a slightly different shifter rod to my know knowledge as well, the section of rod that sits in the shift forks (if you can understand?) is smaller on the steel plate boxes I believe, I suspect you could just grind it down, but it would be easier to drill the hole needed in the JZA80 one. 
My steel plate W58 on the left, norbies modified JZA80 W58 on the right.
aussie260z:
I have a GA70/MA70 position (second most reward), only have an alloy sandwich plate shift fork, not the steel plate one that you are after..., I also have a shifter and inner speedo gear (that goes inside the gearbox to replace the speedo sender) if you are interested.
Cheers
Wilbo
[Updated on: Sat, 05 November 2005 07:59]
|
|
|
| | Subject | Poster | Date |
|---|
 |
Wiring 2jzge into 260z
|
aussie260z | Thu, 21 July 2005 02:24 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Thu, 21 July 2005 04:09 |
|
Re: Wiring 2jzge into 260z
|
Henn | Thu, 21 July 2005 05:39 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Thu, 21 July 2005 05:41 |
|
Re: Wiring 2jzge into 260z
|
Henn | Thu, 21 July 2005 06:48 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Sat, 29 October 2005 06:50 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Sat, 29 October 2005 07:07 |
|
Re: Wiring 2jzge into 260z
|
brett_celicacoupe | Sat, 29 October 2005 07:33 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Sat, 29 October 2005 23:41 |
|
Re: Wiring 2jzge into 260z
|
Manny | Sun, 30 October 2005 01:08 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Mon, 31 October 2005 04:58 |
|
Re: Wiring 2jzge into 260z
|
Manny | Mon, 31 October 2005 05:36 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Mon, 31 October 2005 07:34 |
|
Re: Wiring 2jzge into 260z
|
Alchemist | Mon, 31 October 2005 10:10 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Tue, 01 November 2005 04:59 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Tue, 01 November 2005 05:26 |
|
Re: Wiring 2jzge into 260z
|
sideshow | Tue, 01 November 2005 07:00 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Tue, 01 November 2005 22:38 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Wed, 02 November 2005 08:00 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Wed, 02 November 2005 22:01 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Fri, 04 November 2005 22:22 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Fri, 04 November 2005 23:04 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Fri, 04 November 2005 23:41 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Sat, 05 November 2005 02:31 |
|
Re: Wiring 2jzge into 260z
|
wilbo666 | Sat, 05 November 2005 03:12 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Sat, 05 November 2005 03:33 |
|
Re: Wiring 2jzge into 260z
|
wilbo666 | Sat, 05 November 2005 04:24 |
|
Re: Wiring 2jzge into 260z
|
Norbie | Fri, 11 November 2005 00:10 |
|
Re: Wiring 2jzge into 260z
|
mrshin | Sun, 06 November 2005 08:59 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Thu, 10 November 2005 23:46 |
