| Author | Topic |
|---|
Location:
ACT
Registered:
April 2005
|
|
Re: Wiring 2jzge into 260z
|
Thu, 10 November 2005 23:46
|
 |
wilbo666
"My steel plate W58 on the left, norbies modified JZA80 W58 on the right.
aussie260z:
I have a GA70/MA70 position (second most reward), only have an alloy sandwich plate shift fork, not the steel plate one that you are after..., I also have a shifter and inner speedo gear (that goes inside the gearbox to replace the speedo sender) if you are interested. "
Thanks for the offer champ, but im pretty sure im just going to go the aftermarket gauges,
The speedo and tacho will actually work out cheaper for me if i buy them from the states, instead of getting my Datto ones modified, it should cost somewhere around the $750-$800AUD mark for 4 new gauges, including a 5" electric programable speedo (its like $550AUD in Aussie stores),
As for the shifter, thanks for the replies guys, seems like its relatively straight forward to change the shifter's, here is a pic of where it comes up in the trans tunnell, if i used this shifter location i will have to modify the trans tunnel slightly and the centre console,
http://album.hybridz.org/showphoto.php?photo=3219& amp;cat=500&page=2
Will using the other W 5-spd box shifter location put the shifter in a position were i dont have to modify anything? or will it bring it to far forward???
|
|
|
| | Subject | Poster | Date |
|---|
 |
Wiring 2jzge into 260z
|
aussie260z | Thu, 21 July 2005 02:24 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Thu, 21 July 2005 04:09 |
|
Re: Wiring 2jzge into 260z
|
Henn | Thu, 21 July 2005 05:39 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Thu, 21 July 2005 05:41 |
|
Re: Wiring 2jzge into 260z
|
Henn | Thu, 21 July 2005 06:48 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Sat, 29 October 2005 06:50 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Sat, 29 October 2005 07:07 |
|
Re: Wiring 2jzge into 260z
|
brett_celicacoupe | Sat, 29 October 2005 07:33 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Sat, 29 October 2005 23:41 |
|
Re: Wiring 2jzge into 260z
|
Manny | Sun, 30 October 2005 01:08 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Mon, 31 October 2005 04:58 |
|
Re: Wiring 2jzge into 260z
|
Manny | Mon, 31 October 2005 05:36 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Mon, 31 October 2005 07:34 |
|
Re: Wiring 2jzge into 260z
|
Alchemist | Mon, 31 October 2005 10:10 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Tue, 01 November 2005 04:59 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Tue, 01 November 2005 05:26 |
|
Re: Wiring 2jzge into 260z
|
sideshow | Tue, 01 November 2005 07:00 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Tue, 01 November 2005 22:38 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Wed, 02 November 2005 08:00 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Wed, 02 November 2005 22:01 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Fri, 04 November 2005 22:22 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Fri, 04 November 2005 23:04 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Fri, 04 November 2005 23:41 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Sat, 05 November 2005 02:31 |
|
Re: Wiring 2jzge into 260z
|
wilbo666 | Sat, 05 November 2005 03:12 |
|
Re: Wiring 2jzge into 260z
|
gianttomato | Sat, 05 November 2005 03:33 |
|
Re: Wiring 2jzge into 260z
|
wilbo666 | Sat, 05 November 2005 04:24 |
|
Re: Wiring 2jzge into 260z
|
Norbie | Fri, 11 November 2005 00:10 |
|
Re: Wiring 2jzge into 260z
|
mrshin | Sun, 06 November 2005 08:59 |
|
Re: Wiring 2jzge into 260z
|
aussie260z | Thu, 10 November 2005 23:46 |
