| Author | Topic |
|---|
I supported Toymods
Location:
Perth
Registered:
May 2002
|
 1GGTE clutches
|
Wed, 30 June 2004 08:18
|
 |
Hey guys,
Has anyone got a picture of the bigger Gen3 clutch and flywheel? What size is it exactly?
Thanks,
Nathan
|
|
|
I supported Toymods
Location:
Perth, Western Australia
Registered:
December 2002
|
|
Re: 1GGTE clutches
|
Wed, 30 June 2004 09:13
|
|
|
Yep, I want to see it too, and the specific spring and dampner setup in the centre?!
|
|
|
Location:
Sydney
Registered:
May 2002
|
|
Re: 1GGTE clutches
|
Wed, 30 June 2004 10:21
|
|
gen3 gtes have a 9.5 clutch face
I recently fitted a ~760kg pp with a 5 puck sprung center
should do the job.
|
|
|
I supported Toymods
Location:
Plumpton/sydney
Registered:
November 2003
|
|
Re: 1GGTE clutches
|
Wed, 30 June 2004 12:20
|
|
|
they are the same as 3tgte clutch plate
|
|
|
I supported Toymods
Location:
Perth
Registered:
May 2002
|
|
Re: 1GGTE clutches
|
Wed, 30 June 2004 23:29
|
|
| Bugman wrote on Wed, 30 June 2004 18:21 |
gen3 gtes have a 9.5 clutch face
I recently fitted a ~760kg pp with a 5 puck sprung center
should do the job.
|
Are you sure it's that low? The guy where my clutch was dropped off said it was nearly 2000lbs stock, which is way more than 760kg.
|
|
|
Location:
Sydney
Registered:
May 2002
|
|
Re: 1GGTE clutches
|
Wed, 30 June 2004 23:49
|
|
What exactly do you want photo's of?
I have the flywheel and clutch off a gen3 GA70 supra at home. But the pressure plate is TRD and the clutch plate is brass button. I probably have the original organic plate somewhere but it was probably TRD as well.
The 3T-GTE flywheel does bolt up to a 1G but the clutch is smaller, by half an inch i think (9"). I used a 3T setup on my first 1G and it did the job fine.
Darren.
|
|
|
Location:
Sydney
Registered:
May 2002
|
|
Re: 1GGTE clutches
|
Thu, 01 July 2004 00:09
|
|
|
I have a feeling the standard one was only 500ish KG.
|
|
|
Location:
Sydney
Registered:
May 2002
|
|
Re: 1GGTE clutches
|
Thu, 01 July 2004 00:49
|
|
I got the standard clutch lying in my parents garage I guess i could take a pic of it if it will help.. looks like a clutch though 
|
|
|
Location:
Brisbane
Registered:
May 2002
|
|
Re: 1GGTE clutches
|
Thu, 01 July 2004 00:50
|
|
from this page: http://www.trdsales.com/shop/product.asp?catcode=1 95
The 3rd gen 1ggte clutch plate (TRD part# 31250-SW251) is used in the:
-gx81 twin turbo
-GA70 twin turbo
-JZA80 N/A 5-speedS
-ST215 3S-FE Corona and Carina
-All GT4 Celica's
-SW20 turbo.
The specs they list for the pressure plate are:
diameter: 236mm
standard clamp: 675kgf (6615N)
TRD Spec Clamp: 870kgf (8526N) part# 31210-GA754
The pressure plate is a common part between the late GA70 and GX81's
|
|
|
I supported Toymods
Location:
south of the big smoke
Registered:
May 2002
|
|
|
Registered:
November 2002
|
|
Re: 1GGTE clutches
|
Thu, 01 July 2004 05:14
|
|
|
For what it is worth on that TRD USA parts website, the 5M, 3S-GTE, 7M-GE and 7M-GTE all list a 236mm clutch.
|
|
|
Location:
Sydney
Registered:
May 2002
|
|
Re: 1GGTE clutches
|
Thu, 01 July 2004 05:20
|
|
|
it's only a friction plate for starters and does the r154 have the same input gear as the w58?
|
|
|
I supported Toymods
Location:
Perth
Registered:
May 2002
|
|
Re: 1GGTE clutches
|
Thu, 01 July 2004 09:13
|
|
Interesting, I'll have to see how mine is. It's a 9" one as my engine is a Gen2.
I can't seem to find out anything about the Gen2 one, as everything lists the 236mm one. All I know is mine is now 40% beefier than it left the factory 
|
|
|
