Author | Topic |
I supported Toymods
Location: Perth
Registered: May 2002
|
1G Factory IC Tubing
|
Mon, 12 July 2004 05:30
|
|
Hey guys,
Surely someone has it lying around from a front-cut, I'm after the factory silicon tubing that comes off the cast IC pipes on a 1GGTE. Trying to save some money so I can get the damn thing on the road.
If anyone has some, give us a holler.
Thanks,
Nathan
|
|
|
Registered: November 2002
|
Re: 1G Factory IC Tubing
|
Mon, 12 July 2004 09:52
|
|
Nathan,
Describe this to me mate, diameter and length ? I have some rubber tubing left over from the 1G-GTE I wrecked.
Cheers,
Mitch.
|
|
|
I supported Toymods
Location: Perth
Registered: May 2002
|
Re: 1G Factory IC Tubing
|
Mon, 12 July 2004 10:45
|
|
Not sure on length, it is roughly 2" ID. Its the tubing connected to the cast pipes.
These:
|
|
|
I supported Toymods
Location: Perth
Registered: May 2002
|
Re: 1G Factory IC Tubing
|
Wed, 14 July 2004 03:06
|
|
Bump
|
|
|
Location: newcastle nsw
Registered: May 2002
|
Re: 1G Factory IC Tubing
|
Wed, 14 July 2004 05:59
|
|
i have all custom piping for a standard 1g that doesnt require the rubber pipes, but it goes to a custom intercooler.
|
|
|
I supported Toymods
Location: Perth
Registered: May 2002
|
Re: 1G Factory IC Tubing
|
Wed, 14 July 2004 08:47
|
|
If I can get the silicon bits from there though it's one less bend I have to get made up and I dont need connectors for hooking onto the piping for at least one bit.
|
|
|
Location: sunny coast, qld
Registered: October 2002
|
Re: 1G Factory IC Tubing
|
Thu, 15 July 2004 05:45
|
|
I think I have some, I will check tonight.
|
|
|
I supported Toymods
Location: Perth
Registered: May 2002
|
Re: 1G Factory IC Tubing
|
Thu, 15 July 2004 08:51
|
|
Thanks mate
|
|
|
I supported Toymods
Location: Perth
Registered: May 2002
|
Re: 1G Factory IC Tubing
|
Fri, 16 July 2004 08:28
|
|
Any word guys?
|
|
|
I supported Toymods
Location: Plumpton/sydney
Registered: November 2003
|
Re: 1G Factory IC Tubing
|
Sun, 18 July 2004 12:32
|
|
I have some OH just remembered im using them
|
|
|
I supported Toymods
Location: Perth
Registered: May 2002
|
Re: 1G Factory IC Tubing
|
Mon, 19 July 2004 11:02
|
|
Any word Mitch?
Anyone else NOT using theirs?
|
|
|
Location: south east - melbourne
Registered: March 2004
|
Re: 1G Factory IC Tubing
|
Mon, 19 July 2004 23:54
|
|
good luck mate i was after his same thing sometime ago , finaly one of the guys agreed to send me it , and im still waiting for it , i dunno who it was , and i cant find the thread , so ive given up
|
|
|
Location: Canberra
Registered: May 2002
|
|
|
Location: Adelaide, SA
Registered: May 2002
|
Re: 1G Factory IC Tubing
|
Fri, 23 July 2004 00:47
|
|
It cost me about $200 to get intercooler pipe made up for my 1G JCMF... 2" stainless steel mandrel bent. Add about $150 to that for GOOD hose clamps and 2" high pressure rubber hose.
It might well end up cheaper just getting it done right the first time.
|
|
|
Location: Adelaide, SA
Registered: May 2002
|
|
|