Author | Topic |
Location: Wollongong NSW
Registered: August 2004
|
HELP!!! 2TGEU not firing
|
Tue, 28 September 2004 05:17
|
|
ok...i got 2tgeu engine with weber 45mm sidedraft carby
have been workin on gettg it running but when all timing marks are lined up it wont fire...however when the timing is telling me it is out by quite a bit it runs....
I know the principle is to set everything to start point or 'One'
and everything should be fine.
Could it be the wrong flywheel maybe.....unsure if engine has had conversions.
|
|
|
Location: Dandenong Ranges, VIC
Registered: July 2004
|
Re: HELP!!! 2TGEU not firing
|
Tue, 28 September 2004 08:30
|
|
ive got the same issue with my 2T at the moment, nobody can figure out what is going on. it kicks over if the timing is retarded by 20 degrees plus. very wierd. if you find out please let me know & vice versa.
|
|
|
Location: Adelaide
Registered: May 2002
|
Re: HELP!!! 2TGEU not firing
|
Tue, 28 September 2004 09:28
|
|
try taking the distributor out and rotating it one tooth and then putting it back in...
|
|
|
Location: SYDNEY
Registered: August 2003
|
Re: HELP!!! 2TGEU not firing
|
Tue, 28 September 2004 10:15
|
|
To get the answer I believe we need to know what you did to the motor ie. did you take it apart, removing timing chains.
this would then guide us to whether you have assembled it correctly.as far as tdc no.1 cyl, dizzy set up it should attempt to fire. must be more to it?
|
|
|
Location: Devonport Tasmania
Registered: June 2004
|
Re: HELP!!! 2TGEU not firing
|
Tue, 28 September 2004 11:26
|
|
you need to turn the engine over manually till it is at top dead centre on cylinder 1.
then pull the dizzy cap off any note the rotor button position.
it needs to be lined up exactly where the lead to cylinder 1 would go.
if it doesnt, remove the dizzy and insert again so it lines up.
then all you need to do is tighten it, turn it over and adjust timing till correct.
|
|
|
Location: Adelaide Hills
Registered: January 2004
|
|
|
Location: Wollongong NSW
Registered: August 2004
|
Re: HELP!!! 2TGEU not firing
|
Wed, 29 September 2004 13:53
|
|
Number 1 cylynder TDC.
Dizzy set to Number 1
checked cams all lined up on TDC on first cylinder
Timing is set properly.
Have removed dizzy to line it up on one
points are good. New leads and sparkies.
still cant get it to fire on proper timing marks.
|
|
|
Location: Wollongong NSW
Registered: August 2004
|
Re: HELP!!! 2TGEU not firing
|
Wed, 29 September 2004 13:54
|
|
could it be condenser?
|
|
|
Location: Devonport Tasmania
Registered: June 2004
|
Re: HELP!!! 2TGEU not firing
|
Wed, 29 September 2004 23:18
|
|
pull out spark plug number one, keep the lead on and hold it against your engine/chassis.
turn the car over and see what your spark looks like.
if it looks weak, bypass your ballast resistor and check again.
did it seem better.
does it run with it bypassed ?
if it does its prolly rooted.
if not try a different coil and check spark strength.
|
|
|
Location: Wollongong NSW
Registered: August 2004
|
Re: HELP!!! 2TGEU not firing
|
Sat, 02 October 2004 13:30
|
|
Ok.....the problem has to be alot more obscure....
electricals are all good....
replaced condensor, new leads and plugs, everything lined up right.
Engine not running when timing marks are lined up though will run when marks are sayin its out....
fileing new timing marks on flywheel.
|
|
|
Location: Adelaide Hills
Registered: January 2004
|
Re: HELP!!! 2TGEU not firing
|
Tue, 05 October 2004 01:00
|
|
timing marks should be on the front pulley, and on casing, not flywheel ??
|
|
|
Location: Devonport Tasmania
Registered: June 2004
|
Re: HELP!!! 2TGEU not firing
|
Tue, 05 October 2004 10:19
|
|
its called the harmonic balancer
|
|
|
Location: Castle Hill, Sydney
Registered: February 2004
|
Re: HELP!!! 2TGEU not firing
|
Tue, 05 October 2004 10:32
|
|
mechanical advance?
|
|
|
Location: Wollongong NSW
Registered: August 2004
|
Re: HELP!!! 2TGEU not firing
|
Tue, 05 October 2004 12:55
|
|
er...woops...my bad....harmonic balancer i should have said
|
|
|
Location: Wollongong NSW
Registered: August 2004
|
Re: HELP!!! 2TGEU not firing
|
Tue, 05 October 2004 12:57
|
|
well...short of stripping the engine down for a rebuild i am a lil stumped...but is running ok now though timing marks dont seem to think so...sounds sweet
|
|
|
Location: Castle Hill, Sydney
Registered: February 2004
|
|
|
Location: Wollongong NSW
Registered: August 2004
|
Re: HELP!!! 2TGEU not firing
|
Sat, 09 October 2004 11:19
|
|
ok...got engine firing.
Thanks for suggestions
Though now it seems i have inlet valve problems....the heads comin off.
|
|
|
Location: Wollongong NSW
Registered: August 2004
|
Re: HELP!!! 2TGEU not firing
|
Sat, 09 October 2004 11:20
|
|
oh yea...dizzy is nice. no probs there
|
|
|