Toymods Car Club Inc: Engines, Accessories and other Mechanicals => Dave's clearout sale

Toymods Car Club
www.toymods.org.au

F.A.Q.

Home

Members

Classifieds » Engines, Accessories and other Mechanicals » Dave's clearout sale Show: Today's Posts :: Show Polls Email to friend

Author

Topic

gianttomato
Forums Junkie

I supported Toymods

Location:
I renounced punctuation
Registered:
May 2002

Dave's clearout sale	Wed, 15 December 2004 01:03

M series flywheel and pressure plate (225mm) - $30. M series starter motors 0.7 kW x 3 - $10 _______________________ 1.0 kW - $30 (big mutha) M series altenators MTEU internal reg $30 normal old style $20 4M points distributors $10 each. ($30 the lot - I have about 5) 4M mechanical fuel pump - $10 4M Corona Mk2 intake manifolds x 2 - $10 the lot 4M viscous fan assembly (nice and tight) - $30 4M runs but is uber tired - good for moving a car around a paddock - free (pickup only for this item) 5/6MGE head - free (pickup only) Early M series extractors (square port) suit Corona Mk2 but can be easily modified to fit Crown tentatively sold at $100 - awaiting confirmation F series centre single spinner 4.1:1 not noisy but needs a clean - $50 1UZFE viscous fan assembly - $50 Thermo fan from Crown halfcut low profile (max height 60mm), fan diameter 14" - $50 Complete UZS131 airbox assembly - $50 You pay postage. [Updated on: Wed, 15 December 2004 01:39] [Report message to a moderator]

Toyo Truck
Regular

Location:
Sydney
Registered:
August 2004

Re: Dave's clearout sale	Wed, 15 December 2004 02:38

Hey Dave, Mate is this M series pressure plate and flywheel in ok working order?? will it fit a 7M-GE?? If so, I'll take it. Also, can I hook that crown thermo up to a 12V switch and use it straight away for my conversion? or is it missing bits?? Can you send pics to bart.winter@pulseintl.com.au or post em up on here? Also, you seem to have alot of M series parts, do you have the engine mounts (top half) off a 5M-GE or similar? Cheers, Bart [Report message to a moderator]

gianttomato
Forums Junkie

I supported Toymods

Location:
I renounced punctuation
Registered:
May 2002

Re: Dave's clearout sale

Wed, 15 December 2004 02:58

Here are pics of the thermo fan and flywheel/pressure plate.

The thermo fan is ready to go - you'll need to set up a switch obviously. As you can see it is quite low profile.

The flywheel is from the early series M motors. The bolt pattern is common to ALL M series motors so it will bolt up with no issues. It is however slighly smaller than the 7MGE one as it uses a 225mm pressure plate rather than a 240mm one. I have been in quite a few 7M powered cars and this has never presented a problem.

Attachment: thermo fan 2.jpg
(Size: 113.61KB, Downloaded 33 time(s))
Attachment: thermo fan 1.jpg
(Size: 62.96KB, Downloaded 24 time(s))
Attachment: flywheel and pressure plate.jpg
(Size: 79.83KB, Downloaded 35 time(s))

[Report message to a moderator]

MS-75
Regular

Location:
Adelaide
Registered:
June 2002

Re: Dave's clearout sale	Fri, 13 May 2005 17:16

Sorry to dredge this thread up again dave, but have you still got the extractors mate? there is a bloke I know who could do with them. What other parts have you got for the pld 4m/5m [Report message to a moderator]

CrUZsida
Forums Junkie

I supported Toymods

Location:
Australia
Registered:
November 2003

Re: Dave's clearout sale	Sat, 14 May 2005 06:52

Still got that viscous fan setup? I needs the pulley. [Report message to a moderator]

Previous Topic:	EOI, 3T-GTE T4 high-mount manifold (Melbourne)
Next Topic:	F/S full 3in Exhaust for MZ20 (Adel)

-=] Back to Top [=-

Current Time: Mon Apr 29 12:33:20 UTC 2024

Total time taken to generate the page: 0.0053939819335938 seconds

.:: Contact :: Home ::.