| Author | Topic |
|---|
Registered:
February 2003
|
|
T50 won't slide off engine
|
Wed, 01 June 2005 03:24
|
 |
The bastard won't come off 
I've double, trippled, 100led checked that all bolts are off, gearbox crossmember is unbolted, all ancilleries are off - starte/clutch cyl. but the thing is so attached and stubborn
any tips?
i've tried chisel, hammering it, kicking, jacking it up and down etc
help 
|
|
|
I supported Toymods
Location:
Australia
Registered:
November 2003
|
|
Re: T50 won't slide off engine
|
Wed, 01 June 2005 03:28
|
|
|
Normally I just stick a big screw driver in between the bellhousing and block and just wedge it out.
|
|
|
Location:
Baulkham Hills, Sydney
Registered:
January 2004
|
|
Re: T50 won't slide off engine
|
Wed, 01 June 2005 03:29
|
|
Did u get that bolt right at the top of the gearbox near the heater hoses.
That can be a bastard to find sometimes
U need a HUGE extension to get that 1!
Come round and have a look at my gbox to see where all the bolt holes r if ur stuck.
Just keep tryin des 
|
|
|
Registered:
February 2003
|
|
Re: T50 won't slide off engine
|
Wed, 01 June 2005 03:30
|
|
i got that bolt, it was being a prick too, i couldn't find my 17mm so i had to go and buy one but still it won't come off
hmm, *goes and wedges screwdriver again*
|
|
|
Registered:
May 2002
|
|
|
Registered:
February 2003
|
|
Re: T50 won't slide off engine
|
Wed, 01 June 2005 03:46
|
|
haha by that i mean i tried to pry it with a chisel, and also tried hammering the box in different spots to remove it
|
|
|
Location:
Adelaide
Registered:
May 2003
|
|
Re: T50 won't slide off engine
|
Wed, 01 June 2005 03:50
|
|
|
The AE86 engines had a pair of stays on the bottom of the engine block which connected to four bolts on the front side of the engine.
|
|
|
I supported Toymods
Location:
Perth, WA
Registered:
May 2003
|
|
Re: T50 won't slide off engine
|
Wed, 01 June 2005 04:04
|
|
hmm
cant say i've ever had this problem
id say there would be some bolts still in there.
u taken the starter motor out?
shifter?
|
|
|
Registered:
May 2002
|
|
Re: T50 won't slide off engine
|
Wed, 01 June 2005 04:17
|
|
Maybe the metal pole coming out of the gearbox and attached to the thing at the back of the car that makes the wheel turn is still attached and is inhibiting the sliding action
Sorry, couldn't help it 
Perhaps you can fix it with fireworks! (Remember that classic Simpsons episode )
|
|
|
Location:
brisbane
Registered:
October 2004
|
|
|
Location:
brisbane
Registered:
October 2004
|
|
|
Registered:
February 2003
|
|
Re: T50 won't slide off engine
|
Wed, 01 June 2005 04:37
|
|
ok it's out 
|
|
|
Location:
brisbane
Registered:
October 2004
|
|
Re: T50 won't slide off engine
|
Wed, 01 June 2005 07:16
|
|
|
and the problem was?
|
|
|
Location:
Sydney/Wollongong
Registered:
October 2004
|
|
Re: T50 won't slide off engine
|
Wed, 01 June 2005 07:35
|
|
|
I've got $10 on shifter..
|
|
|
Registered:
February 2003
|
|
Re: T50 won't slide off engine
|
Wed, 01 June 2005 07:39
|
|
LOL
The weight of the gearbox, as ke382TG suggested, i jacked it up horizontally and got into kung fu position
|
|
|
Location:
Canberra
Registered:
May 2002
|
|
Re: T50 won't slide off engine
|
Wed, 01 June 2005 07:50
|
|
good work
Did you bust a gearbox with the newfound power of the turbo setup??
|
|
|
Registered:
February 2003
|
|
Re: T50 won't slide off engine
|
Wed, 01 June 2005 14:54
|
|
clutch
gearbox is next tho, it's on its last legs
|
|
|
I supported Toymods
Location:
sydney.au
Registered:
August 2002
|
|
Re: T50 won't slide off engine
|
Wed, 01 June 2005 15:34
|
|
hehe
good one des. 
|
|
|
Location:
Sydney
Registered:
September 2004
|
|
Re: T50 won't slide off engine
|
Thu, 02 June 2005 12:05
|
|
Time for a w5* upgrade then eh? 
|
|
|
Location:
Canberra
Registered:
May 2002
|
|
Re: T50 won't slide off engine
|
Thu, 02 June 2005 12:08
|
|
|
sounds like it!
|
|
|
Location:
Baulkham Hills, Sydney
Registered:
January 2004
|
|
Re: T50 won't slide off engine
|
Sun, 05 June 2005 06:16
|
|
|
pm sent regarding the clutch prob...
|
|
|
