| Author | Topic |
|---|
Registered:
September 2005
|
|
oil cooler on a 20V
|
Mon, 05 September 2005 08:38
|
 |
what sandwich plate do i use to fit an oil cooler on a 20V? where from and how much?
also
theres a bolt in the block above the oil press sender unit on the exhaust side on the 20V, is this tapped into the oil system, i figure it is due to its location next to the pump and oil press sender. If it is can i remove the bolt and fit a fitting and use this as my oil feed for turbo?
cheers
|
|
|
I supported Toymods
Location:
Perth
Registered:
October 2003
|
|
Re: oil cooler on a 20V
|
Mon, 05 September 2005 12:18
|
|
|
AE82 Oil Cooler Sandwhich plate ? I cant see why that wouldnt fit, and i have heard of people using the oil sender hole for the turbo feed such as monkey with the light blue 4agte..
|
|
|
Registered:
September 2005
|
|
Re: oil cooler on a 20V
|
Mon, 05 September 2005 12:23
|
|
|
yeah thats putting a T piece in the oil pressure switch. i dont want to do that but i want to know what the bolt is for next to it
|
|
|
Location:
Sydney
Registered:
November 2003
|
|
Re: oil cooler on a 20V
|
Tue, 06 September 2005 01:19
|
|
are you after something like this?
this is on a 16v block but i was thinking about using the same setup on my N/A 20v as its alot more compact that the AE92 sandwich plate which fouls my KE side engine mount.
| Skaney wrote on Wed, 10 August 2005 18:09 |
It came with the oil cooler in a kit. But I think you can by them seperate. Has a Thermostat in it, alot of aftermarket ones dont.
I got it through Dr. Drift.
|
| Skaney wrote on Wed, 10 August 2005 20:21 |
Whole kit was $180 inc hoses, fittings and the cooler.
Look for him on nissansilvia.com
|
hope that helps
| bluehachi wrote on Mon, 05 September 2005 18:38 |
theres a bolt in the block above the oil press sender unit on the exhaust side on the 20V, is this tapped into the oil system, i figure it is due to its location next to the pump and oil press sender.
|
can u take a photo of this please?
|
|
|
Registered:
September 2005
|
|
Re: oil cooler on a 20V
|
Tue, 06 September 2005 07:40
|
|
yeah thats what im after, dont need the kit as i already have fittings and lines + cooler. just need the sandwich plate.
|
|
|
Registered:
September 2005
|
|
Re: oil cooler on a 20V
|
Tue, 06 September 2005 07:44
|
|
also that bolt.. your block has it also.
|
|
|
Location:
Sutherland Shire
Registered:
April 2003
|
|
Re: oil cooler on a 20V
|
Tue, 06 September 2005 10:22
|
|
|
An ae92 sandwich plate will foul on the rwd engine mount
|
|
|
Location:
Sydney
Registered:
April 2005
|
|
Re: oil cooler on a 20V
|
Wed, 07 September 2005 02:26
|
|
| 4a-c wrote on Tue, 06 September 2005 20:22 |
An ae92 sandwich plate will foul on the rwd engine mount
|
i don't believe the 4ag fwd factory oil cooler sandwich plate fouls on 4ag rwd motor. this setup being used on 4 ae86's, works fine for all of them. have a got pic but cant firgure out how to post.
|
|
|
Location:
Adelaide
Registered:
August 2003
|
|
Re: oil cooler on a 20V
|
Wed, 07 September 2005 07:12
|
|
Simon thats my 16v block with the oil cooler.
Im pretty sure Dr Drift can sell you just the sandwhich plate. Has a thermostat too.
I think I remember reading somewhere that the bolt hole you are talking about is a coolant drain?
|
|
|
Location:
Sydney (Campbelltown...!)
Registered:
December 2003
|
|
Re: oil cooler on a 20V
|
Wed, 07 September 2005 10:17
|
|
yes it is a coolant drain plug
|
|
|
Registered:
September 2005
|
|
Re: oil cooler on a 20V
|
Thu, 03 November 2005 07:37
|
|
bumpy.
what i want to know is what is the thread pitch size for the oil filter? i am about to order a sandwich plate and need to know
|
|
|
