Toymods Car Club Inc: Tech & Conversions => 4agze head gasket

Toymods Car Club
www.toymods.org.au

Toymods » Tech & Conversions » 4agze head gasket Show: Today's Posts :: Show Polls Email to friend

Author

Topic

Location:
sydney
Registered:
March 2003

4agze head gasket	Thu, 01 September 2005 06:41

Hi guys... i would like the 2mm head gasket as i have read. any recommendations on sizes guys?i will be running 14 psi boost on standard super charger. Also any ideas for which is the best place to get it? someone quoted me over $400 bucks for a headgasket from hks.. i think the guy had rocks in his head... thanks guys... and YES i have tried searching... [Updated on: Thu, 01 September 2005 06:42] [Report message to a moderator]

1200det
Forums Junkie

Location:
Canberra
Registered:
September 2003

Re: 4agze head gasket	Thu, 01 September 2005 07:06

A genuine Toyota gasket will not have any issues coping with what your going to throw at it [Report message to a moderator]

Location:
sydney
Registered:
March 2003

Re: 4agze head gasket	Thu, 01 September 2005 07:38

well if thats the case what is the standard thickness of a gze hg? i can get a trd 0.8 and 1.1 mm thickness cheap. might even get that instead. any other opinions...i read a few guys running 2mm hg. whats with that? thanks again [Report message to a moderator]

Big T
Forums Junkie

Location:
Sydney
Registered:
September 2004

Re: 4agze head gasket	Thu, 01 September 2005 12:18

Are you decking the block? A 2mm hg could possibly ruin your squish areas for the sake of running a couple more psi. $400!?!?! The dude must be nuts... i got my 1.6mm metal HKS hg for $170 shipped from Japan. It would've been the same price if it was the 2mm one. If you can get TRD 0.8mm for cheap, you could do a dodgy and use 2 of them stuck together. I think the genuine GZE gasket is 1.25mm? Don't quote me on that one though. Eddie. [Report message to a moderator]

Location:
sydney
Registered:
March 2003

Re: 4agze head gasket	Mon, 05 September 2005 03:23

thanks big T. which site did u get the hg from? mind if i shop there as well.. also.. i found this site http://www.hks-power.co.jp/products/engine/metal/m etal.html it doesnt list a 1.6mm hg. have a look. [Updated on: Mon, 05 September 2005 03:35] [Report message to a moderator]

Big T
Forums Junkie

Location:
Sydney
Registered:
September 2004

Re: 4agze head gasket	Mon, 05 September 2005 04:41

Greenline Motorsports. http://www.greenline.jp/ They have some pretty good stuff at reasonable prices... just make sure you factor in the shipping as well. Note that i also ordered the "bead type" gasket, not the stopper one as they didn't have 1.6mm in stopper form. Eddie. [Report message to a moderator]

fatmr2
Forums Junkie

Location:
sydney
Registered:
November 2003

Re: 4agze head gasket	Mon, 05 September 2005 13:01

I ran the standard head gasket with 22.5 psi and i had no problems at all [Report message to a moderator]

Location:
sydney
Registered:
March 2003

Re: 4agze head gasket	Thu, 08 September 2005 04:10

thanks everyone.. after a bit of research i an get custome made one but for my application its probly not worth it.. standard hg it is.. thanks again [Report message to a moderator]

Previous Topic:	2t/3tgeu parts to rebuild 3tgte?
Next Topic:	CAM Gears for 1GGTE

Current Time: Mon Apr 29 12:41:08 UTC 2024

Total time taken to generate the page: 0.0096549987792969 seconds

.:: Contact :: Home ::.