Toymods Car Club
www.toymods.org.au
F.A.Q. F.A.Q.    Register Register    Login Login    Home Home
Members Members    Search Search
Toymods » Members Rides » Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion

Show: Today's Posts  :: Show Polls 
Email to friend 
Switch to threaded view of this topic Create a new topic Submit Reply
AuthorTopic
Sam_Q
Forums Junkie


Location:
S.E suberbs, Vic
Registered:
December 2003
 
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Tue, 27 September 2005 12:11 Go to previous messageGo to next message
sorry for the delay bobski, i dont know what model of landcruiser its off, I got it off ebay and they couldn't tell me. I will geta pic though for everyone else out there who wants one, it really does fit better than the original and is a great upgrade.

As for the brake bias valve I took the guts out of it for the initial proportioning which is only suitable for drums. Heres the info courtesy of Accoustic:

http://www.my-acoustic.com/Car/brakes/rear_efficie ncy/rear_efficiency.htm
  Send a private message to this user    
Sam_Q
Forums Junkie


Location:
S.E suberbs, Vic
Registered:
December 2003
 
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Tue, 27 September 2005 15:12 Go to previous messageGo to next message
Well the time has finally come:

http://sam.theicy.net/auto/transplant.jpg

This is the stage that I am at right now. My loom is in, the 4Ac is out, the 4AGE is in RWD form and the old alternator wiring has been taken out by myself (took a while).


Bobski: Heres my master, anyone have any idea what it's off?

http://sam.theicy.net/auto/master.jpg


Also notice my adjustable shockers and the plates that will be the start of the construction of my strut brace. A big thanks to Pete for those.


and lastly a proper shot of my fabricated alternator bracket which still needs to be aligned:

http://sam.theicy.net/auto/altbracket3.jpg

[Updated on: Tue, 27 September 2005 15:40]

  Send a private message to this user    
Sam_Q
Forums Junkie


Location:
S.E suberbs, Vic
Registered:
December 2003
 
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Tue, 27 September 2005 15:38 Go to previous messageGo to next message
Last time I took my 20V out it had no engine hooks, so I ended up lifting it with a sling that went under the throttle bodies, yes I lifted the whole engine by the throttles! For bloody obvious reasons I wanted to avoid doing that again so I took the ones off the 4Ac engine and modified them to fit. Heres how they look:

This one was shortened, had a plate welded on to extend it from the side and then redrilled:

http://sam.theicy.net/auto/engine/sidehook.jpg


This one was chopped, extended and drilled:

http://sam.theicy.net/auto/engine/rear.jpg

Also notice the rear transfer plate in place and the side outlet.
  Send a private message to this user    
Sam_Q
Forums Junkie


Location:
S.E suberbs, Vic
Registered:
December 2003
 
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Tue, 27 September 2005 15:48 Go to previous messageGo to next message
More of my RWD conversion bits:



http://sam.theicy.net/auto/cooling/sidepipe.jpg

My modified 4Ac rear water pipe, this ones for my heater water supply.





My custom water outlet pipe I made bolted in place. It was made to hold both sensors and to also hold the original 20V dipstick in place.

http://sam.theicy.net/auto/cooling/outlet.jpg
http://sam.theicy.net/auto/cooling/side.jpg
  Send a private message to this user    
mikes86
Regular


Location:
goldy coast
Registered:
September 2004
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Wed, 28 September 2005 09:56 Go to previous messageGo to next message
This has to be the best build up I have ever watched. When i go to do my 20v conversion this will be my bible because everything is so neat and well made. Keep up the top work champ!
  Send a private message to this user    
Sam_Q
Forums Junkie


Location:
S.E suberbs, Vic
Registered:
December 2003
 
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Thu, 29 September 2005 00:51 Go to previous messageGo to next message
thanks Mike, whwn that day does come and you are unsure about something let us know and I will do my best to help you.
  Send a private message to this user    
Sam_Q
Forums Junkie


Location:
S.E suberbs, Vic
Registered:
December 2003
 
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Thu, 29 September 2005 07:09 Go to previous messageGo to next message
Well at the moment my car is seriously pissing me off. It goes to show that no matter how carefully I plan things shit still happens. My airbox is useless, I couldnt syphon the tank out, my extractors cant be modified easy and have to be left alone, I dont have enough of the right materials to do the exhaust and the list goes on. Ontop of all that I have had time working against me even though I am having time off at the moment.

Anyway it hasn't been all loses, I did get lucky with something:

I was once again at Super Cheap Auto (love that joint!) and I looked through the pile of radiator/heater hoses and I found one that I thought I could use for my engine, It was off a Gemini. they also had a brass adapter to join the pipe. I took it home, chopped it in the middle, added the joiner, rotated it on the join 180 degrees, clamped it back up and then cut a shoprt section off one end. It fit like it was made for the job, not bad considering I didn't measure anything.

Here is what it looked like after I modified it:

http://sam.theicy.net/auto/cooling/rearpipe1.jpg

For those who can't read it it says "heater hose to suit Holden Gemini", also included in the pic is the packet for the brass joiner



this is how its meant to plug up:

http://sam.theicy.net/auto/cooling/rearpipe2.jpg

One end goes to the heater core water supply valve and the other to the outlet on the engine head.
  Send a private message to this user    
ae86 Drifter
Regular


Location:
newcastle
Registered:
January 2004
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Mon, 03 October 2005 12:55 Go to previous messageGo to next message
i love this shit.lol.engine setup is awesome just like mine,
cheers sam keep me updated Smile Very Happy
  Send a private message to this user    
monkeymajik
Forums Junkie


Location:
Brisbane
Registered:
February 2003
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Mon, 03 October 2005 13:45 Go to previous messageGo to next message
Looking good.

That M/C is off a toyota light commercial. Hiace type stuff.
  Send a private message to this user    
Sam_Q
Forums Junkie


Location:
S.E suberbs, Vic
Registered:
December 2003
 
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Mon, 03 October 2005 15:54 Go to previous messageGo to next message
well unfortunetly my camera has died a quick death by the hands of salty water (don't ask) so updates might be a bit uninteresting for a while. I will try and borrow a camera when i do need it. A better one is on the way, so hopefully that means less grainy pics.

I managed to finish my extractors, I am so pushed for space that I hammered the underside of the body a little and also couldn't fit a flange under there. So I will most likely have my extractors, the collector, the flex pipe and then at the end of the flex I will have a flange. Sprinters realy are shocking when it comes to room under them near the firewall. The reason I am cutting so close is because I am making sure that when I hit the subframe just behind the front wheels I want to make sure that it hits just that; the sub-frame, not my extractors. The whole system start to finish doesn't at any one point drop lower than the body of the car, quite a difficult thing to do I must say. This is the price I pay for having such a low car. Oh well it will atleast give me one less thing thats going to wreck my system.
  Send a private message to this user    
Sam_Q
Forums Junkie


Location:
S.E suberbs, Vic
Registered:
December 2003
 
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Mon, 03 October 2005 16:06 Go to previous messageGo to next message
thought I would show up a pip of how my engine looks almost complete:

http://sam.theicy.net/auto/engine/20v.jpg
  Send a private message to this user    
Sam_Q
Forums Junkie


Location:
S.E suberbs, Vic
Registered:
December 2003
 
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Sun, 16 October 2005 23:04 Go to previous messageGo to next message
I managed to borrow a digital camera off a friend so I have pictures again after a while.

after a huge amount of trouble my stainless exhaust is finally almost done. I still don't know if the pipes will crack with the steel welds but I am going to find out. I won't have pictures of it fitted under the car for a while but heres how it looks on the floor:

http://sam.theicy.net/auto/exhaust/pipesdone1.jpg

http://sam.theicy.net/auto/exhaust/pipesdone2.jpg

http://sam.theicy.net/auto/exhaust/pipesdone3.jpg


notice the metal cat in the middle. It is the smallest size of 2.5 inch and I know it's a complete overkill but I mainly bought it for its size, thanks to John from Importbitz for that one. The pipe betwen the cat and the flex is actually 2.5 inch to suit the cat but it's been reduced to 2.25 on the other end and of course all changes in size are gradual and smooth.
  Send a private message to this user    
Sam_Q
Forums Junkie


Location:
S.E suberbs, Vic
Registered:
December 2003
 
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Sun, 16 October 2005 23:25 Go to previous messageGo to next message
Heres my master cylender now connected up with some custom brake lines (thanks once again to Rowvile brake and clutch):

http://sam.theicy.net/auto/master2.jpg

I sure hope I got it right with which pipe goes where. I would assume it's the same setup as the sprinter but you never know.
  Send a private message to this user    
Sam_Q
Forums Junkie


Location:
S.E suberbs, Vic
Registered:
December 2003
 
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Sun, 16 October 2005 23:32 Go to previous messageGo to next message
I have now also finished my airbox, this is what I managed to do previously:

http://sam.theicy.net/auto/engine/trumpets4.jpg

and I thought I couldn't use it because I didn't have the room. Well I managed to fit a banjo fitting on the master cylender and I also came up with an airbox design that allowed enough room for it. So heres how I started:

http://sam.theicy.net/auto/engine/airbox1.jpg

and with the trumpets in place:

http://sam.theicy.net/auto/engine/airbox2.jpg

  Send a private message to this user    
Sam_Q
Forums Junkie


Location:
S.E suberbs, Vic
Registered:
December 2003
 
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Sun, 16 October 2005 23:45 Go to previous messageGo to next message
this is how it turned out:

http://sam.theicy.net/auto/engine/airbox3.jpg
http://sam.theicy.net/auto/engine/airbox4.jpg
http://sam.theicy.net/auto/engine/airbox5.jpg

it turned out way better than I expected. Usually anything i make is more shonky looking than this so I suprised myself. I will have to wait to see if I allowed for enough room for the engine to rock side to side.

The box did however warp when I made this and it doesnt sit that well anymore on the rubber seal. I am hoping that it will seal ok when the bolts pull it down when I tighten it up.

I also need to drill some of the original nuts out and weld them in the top instead, this is because I can't access the top anymore to do up the originals, I will have to do it from the bottom.


This is however still only a temporary setup, i plan to have a low mount airbox with long trumpets feeding it, but that's later on.
  Send a private message to this user    
Sam_Q
Forums Junkie


Location:
S.E suberbs, Vic
Registered:
December 2003
 
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Sun, 16 October 2005 23:53 Go to previous messageGo to next message
and finally howmy engine is looking now:

http://sam.theicy.net/auto/engine/4age.jpg
  Send a private message to this user    
DRFT - 86
Regular


Location:
Batemans Bay, NSW
Registered:
February 2005
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Mon, 17 October 2005 05:11 Go to previous messageGo to next message
great work champ... coming along nicely....
  Send a private message to this user    
Dale_ta22
Regular


Location:
Forster NSW
Registered:
September 2004
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Tue, 18 October 2005 11:06 Go to previous messageGo to next message
I just read through from start to finish. That's an absolutely awesome write up so far.. inspirational to me (to get a new project!). I'm in awe of all you've done! Shocked
  Send a private message to this user    
Sam_Q
Forums Junkie


Location:
S.E suberbs, Vic
Registered:
December 2003
 
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Tue, 18 October 2005 16:55 Go to previous messageGo to next message
thanks guys,

unfortunetly me doing everything myself also has it's downsides, I have a limited amount of time and my neighbour is about to go on a rampage that's enduced by permement grinder sounds coming from my garage on a Saturday. Unless your a car fan or have a hearing problem you dont want live near me!
  Send a private message to this user    
domasik
Forums Junkie


Location:
Sydney
Registered:
November 2003
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Tue, 18 October 2005 23:04 Go to previous messageGo to next message
sam you can come live with me and have my sisters babies for all i care so long as you teach me all your customisation skills and bring your welder!!! hhehehehe
  Send a private message to this user    
Sam_Q
Forums Junkie


Location:
S.E suberbs, Vic
Registered:
December 2003
 
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Wed, 19 October 2005 07:54 Go to previous messageGo to next message
hehehehe, let me think about it! Wink
  Send a private message to this user    
shinybluesteel
Forums Junkie


I supported Toymods

Location:
melbourne
Registered:
June 2002
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Wed, 19 October 2005 13:11 Go to previous messageGo to next message
Hey sam, nice log you got there.

i met a dude who i think you know at work, andrew, drives a white auto R31.

a small point on the water conversion, does blocking off all those outlets/inlets mean that you are not circulating water through the block when the thermostat is closed? i'm running a smallport in my AE86 (fwd motor too) and i didnt have to block off anything.


Keep up the good work!

[Updated on: Wed, 19 October 2005 13:22]

  Send a private message to this user    
Sam_Q
Forums Junkie


Location:
S.E suberbs, Vic
Registered:
December 2003
 
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Wed, 19 October 2005 14:32 Go to previous messageGo to next message
thanks,

ah yes, I went to school with that Andrew, nowdays we mostly have a mutual friend in common.

As for the outlet/inlet from the head, i didn't block them off, that plate has a slot cut into it. What I effectivly did is instead of the inlet/outlet being at the back and the water bypassing at the front I reversed it. Now the water comes out the back of the head only to be diverted into the other outlet by the slot in my thick aluminium plate. Now the cooling system is the same layout as all 16V engines. Your engine being a 16V automaticly takes the water out the front end of the engine so your fine. It's a head design thats unique to the 20V engines that causes the problems, that's why you don't have them.
  Send a private message to this user    
shinybluesteel
Forums Junkie


I supported Toymods

Location:
melbourne
Registered:
June 2002
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Thu, 20 October 2005 10:25 Go to previous messageGo to next message
cool, just didnt want you to go cooking your engine Very Happy
  Send a private message to this user    
Phrostbyte
Forums Junkie


I supported Toymods

Location:
Frankston, Victoria
Registered:
April 2004
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Sun, 23 October 2005 12:49 Go to previous messageGo to next message
Can't wait to finally see it running Sam, should be insane Very Happy.

Four weeks till the night cruise, and I'll be down in melb from friday afternoon till the saturday night of the cruise, so I'll be happy to help until late friday night if you don't have it done by then.

The amount of experience I've earned in the past 4 weeks is amazing, a 4AGE conversion is definetely a worth-while experience, especially in your case, doing everything right down to the last little smidgeon, I'll say it again, amazing work Sam... Razz


Kev.
  Send a private message to this user    
Sam_Q
Forums Junkie


Location:
S.E suberbs, Vic
Registered:
December 2003
 
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Thu, 27 October 2005 11:15 Go to previous messageGo to next message
thanks Kev, I am unsure how close I will cut it till the cruise. There are far too many variables in the way to say for sure. I might do a dodge with the wiring loom for now just to get it running.

It is worthwhile experience, but for me it has been a very tedious process. My brain keeps telling me to quit saying stuff like that the rice up boys in their Silvias will always be faster than me in a staight line, well maybe not on a windy road if they crash but still.. But I know I will have a lighter, more nimble, more original, better engeneered car than just about all of the Nissan s-1x's or 180sx's. I will use heaps less fuel too, with my other engine and managemant system I am aiming for 7L/100.

After I get it running I think then it will start to be rewarding. Then I get to make and fine-tune my setup to make it really professional. I will make my wild intake, hide my wiring, tune it to the absolute max, install my water injection, etc.. the funs just about to start
  Send a private message to this user    
Sam_Q
Forums Junkie


Location:
S.E suberbs, Vic
Registered:
December 2003
 
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Tue, 01 November 2005 03:07 Go to previous messageGo to next message
making some progress, still a bit slow though:

http://sam.theicy.net/auto/engine/4age2.jpg

- Driveline is back in

- Airbox is almost ready

- Experiencing problems with my fuel tank mods

- Exhaust is mostly in but waiting on having an oxy sensor plug welded on.

- Wiring almost done... I think
  Send a private message to this user    
Sam_Q
Forums Junkie


Location:
S.E suberbs, Vic
Registered:
December 2003
 
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Tue, 01 November 2005 03:16 Go to previous messageGo to next message


well my exhaust fits nice and close, heres a test fit:

http://sam.theicy.net/auto/exhaust/under1.jpg

http://sam.theicy.net/auto/exhaust/under2.jpg
  Send a private message to this user    
Phrostbyte
Forums Junkie


I supported Toymods

Location:
Frankston, Victoria
Registered:
April 2004
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Tue, 01 November 2005 03:55 Go to previous messageGo to next message
Can you say... absolute perfection? Hahah Sam dude, that exhaust is absolutely insane! Bet it's going to sound insane too Smile

Kev.
  Send a private message to this user    
Sam_Q
Forums Junkie


Location:
S.E suberbs, Vic
Registered:
December 2003
 
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Tue, 01 November 2005 04:45 Go to previous messageGo to next message
not quite Kev, to be honest the steel welds on the stainless pipes has got me worried, on the main section it should be ok but on the extractors who knows.

As for the sound, I am confident it will be good, I hope it won't be too loud, ah either way i will probably put a butterfly valve in the middle.
  Send a private message to this user    
Sam_Q
Forums Junkie


Location:
S.E suberbs, Vic
Registered:
December 2003
 
Re: Project 86 - Big technical worklog with 20V + diff + brake + suspension conversion Thu, 17 November 2005 15:51 Go to previous message

This worklog has been moved to here:


http://www.toymods.net/forums/showthread.php?t=503
  Send a private message to this user    
Pages (4): [ «  <  1  2  3  4]   Switch to threaded view of this topic Create a new topic Submit Reply
Previous Topic:Lexus IS200 (250?)
Next Topic:MY NEW 101 LEVIN
Goto Forum:
-=] Back to Top [=-

Current Time: Thu Mar 28 14:14:47 UTC 2024

Total time taken to generate the page: 0.0068831443786621 seconds

Bandwidth utilization bar

.:: Contact :: Home ::.

Powered by: FUDforum 2.3.8
Copyright ©2001-2003 Advanced Internet Designs Inc.