Toymods Car Club
www.toymods.org.au
F.A.Q. F.A.Q.    Register Register    Login Login    Home Home
Members Members    Search Search
Toymods » Tech & Conversions » 3sgte vs 3sge block

Show: Today's Posts  :: Show Polls 
Email to friend 
Switch to threaded view of this topic Create a new topic Submit Reply
AuthorTopic
MR. 2
Forums Junkie


Location:
Parramatta
Registered:
July 2002
3sgte vs 3sge block Wed, 19 October 2005 23:15 Go to next message
what is the differance between them if any???
both gen 2 3sgte and gen 2 3sge???
can it be used for a 3sgte??
  Send a private message to this user    
JustenGT4
Forums Junkie


Location:
Canberra
Registered:
June 2003
Re: 3sgte vs 3sge block Thu, 20 October 2005 02:25 Go to previous messageGo to next message
No oil squirters for the underside of the pistons in the n/a block. No oil feed for the turbo either.

They are definitely different castings from factory as well so sure there must be some structural differences but have never looked into it.
  Send a private message to this user    
RAV-GT4
Forums Junkie


Toymods member
I supported Toymods

Location:
Rydalmere, NSW
Registered:
May 2002
 
Re: 3sgte vs 3sge block Thu, 20 October 2005 03:08 Go to previous messageGo to next message
What Justen said is probably the only noticeable block differences you'll find... the rest are in the sump, sump ass'y, head, etc. Both are still same bore x stroke (86mm x 86mm). Also some have 2-bolt mains, some have 4-bolt. I think from memory the ST205 block had 4-bolt mains and the ST185 block had the 2-bolt. Confused
  Send a private message to this user    
MR. 2
Forums Junkie


Location:
Parramatta
Registered:
July 2002
Re: 3sgte vs 3sge block Thu, 20 October 2005 03:28 Go to previous messageGo to next message
bugger then that rules that out. just found a 3sge block well i should say they are everywhere but no 3sgte ones floating around.

thanks for that guys it helps.
  Send a private message to this user    
spectral
Forums Junkie


Location:
Brisbane
Registered:
February 2003
Re: 3sgte vs 3sge block Fri, 21 October 2005 01:11 Go to previous messageGo to next message
Some early 3SGE have the mount holes bossed and tapped for RWD (north south) setup as well. 3SGTE don't from appearances, and will require a bit of creativity. From your avatar, this wouldn't be an issue for you of course, owning a SW20.
  Send a private message to this user    
ST185 Bourkey
Newcomer


Location:
Robertson
Registered:
October 2005
Re: 3sgte vs 3sge block Sun, 06 November 2005 10:19 Go to previous messageGo to next message
I have a 3S-GTE sitting in a paddock at home.
http://www.nfiracing.com/nfi/modules/Coppermine/albums/userpics/10029/102_1335640x483.jpg
  Send a private message to this user    
havabeer
Forums Junkie


Location:
new castle
Registered:
July 2005
Re: 3sgte vs 3sge block Sun, 06 November 2005 10:33 Go to previous message
if you ever need someone to take that 3s-gte off your hands for free bourkey, just give me a call Very Happy Wink
  Send a private message to this user    
  Switch to threaded view of this topic Create a new topic Submit Reply
Previous Topic:putting a shim in a brake caliper..ok for track use?
Next Topic:Overheating problems
Goto Forum:
-=] Back to Top [=-

Current Time: Thu Apr 18 09:28:42 UTC 2024

Total time taken to generate the page: 0.0050771236419678 seconds

Bandwidth utilization bar

.:: Contact :: Home ::.

Powered by: FUDforum 2.3.8
Copyright ©2001-2003 Advanced Internet Designs Inc.