| Author | Topic |
|---|
Location:
wollongong
Registered:
March 2004
|
|
20v timing belt
|
Thu, 03 November 2005 03:24
|
 |
What will happen if I don't change my timing belt until it breaks, as it's a non interference head the valves won't hit the pistons. Will it damage anything else? I don't want to change the belt because its going to cost me stupid amounts to have one imported through toyota.
I figure the 100,000k limit has to have a safety factor built into it, so the belt will probably last for a fair while after that.
|
|
|
Location:
Canberra
Registered:
May 2002
|
|
Re: 20v timing belt
|
Thu, 03 November 2005 03:45
|
|
A Camira belt is 1mm wider, but, otherwise identical. It works perfectly.
You might have to take your belt in to compare it as there might be different Camira belts out there.
|
|
|
Location:
Sydney
Registered:
February 2004
|
|
Re: 20v timing belt
|
Thu, 03 November 2005 04:15
|
|
Castle Hill Toyota stocks timing belts for a 20v. I changed mine when I put my 20v in my AE93. I've been told that most Toyota spares depts will supply imported bits if you give them the number. It wasn't very expensive. I'd need to check my reciept at home but according to a list that I downloaded from the net some the part number is: 13568-19035
Toby
|
|
|
Location:
Sydney
Registered:
November 2003
|
|
Re: 20v timing belt
|
Thu, 03 November 2005 06:24
|
|
how much are these costing from toyota?
the quotes i got from auto one for what they belive to be a match (still have to double check it to confirm its the right one) is $83.80
110 teeth & 21mm wide.
bill sherwood states a LADA one will fit BUT the parts catalauge says that there 111 teeth?
|
|
|
Registered:
September 2005
|
|
Re: 20v timing belt
|
Thu, 03 November 2005 07:38
|
|
nothing will happen if it breaks/slips
i have had mine slip twice now while at 8800 rpm, nothing happened mechanically apart from a sever loss of power from skipping 3 teeth.
stupid toyota belt tensioners
|
|
|
I supported Toymods
Location:
Sutho/Hills NSW
Registered:
September 2002
|
|
|
Location:
Sydney
Registered:
November 2003
|
|
Re: 20v timing belt
|
Thu, 03 November 2005 11:13
|
|
|
PM SENT. ITS MINE FELLAS!!!!
|
|
|
Location:
wollongong
Registered:
March 2004
|
|
Re: 20v timing belt
|
Thu, 03 November 2005 11:17
|
|
|
bullshit, it's my thread i saw it first!
|
|
|
Location:
Sydney
Registered:
November 2003
|
|
Re: 20v timing belt
|
Thu, 03 November 2005 21:39
|
|
| domasik wrote on Thu, 03 November 2005 17:24 |
how much are these costing from toyota?
the quotes i got from auto one for what they belive to be a match (still have to double check it to confirm its the right one) is $83.80
110 teeth & 21mm wide.
bill sherwood states a LADA one will fit BUT the parts catalauge says that there 111 teeth?
|
in referance to this post, the parts cataluage is listing a 4ageu timing belt and i checked my 20v belt and it had 111 written on it, obviously meaning 111 teeth, meaninig the lada one will probably fit.
|
|
|
Location:
eastern suburbs, melbourne
Registered:
March 2005
|
|
Re: 20v timing belt
|
Thu, 03 November 2005 21:59
|
|
| kewp wrote on Thu, 03 November 2005 22:17 |
bullshit, it's my thread i saw it first!
|
offer more for it.
|
|
|
Location:
Canberra
Registered:
November 2004
|
|
Re: 20v timing belt
|
Tue, 08 November 2005 11:50
|
|
|
Camira and Lada both have 111 tooth 19mm wide belt, but the lada has the correct type of ribs: as in round , camira has square. Lada timing belt gates- $34.00 [trade]from repco.
|
|
|
Location:
Canberra
Registered:
May 2002
|
|
Re: 20v timing belt
|
Tue, 08 November 2005 20:51
|
|
| 4ag20t wrote on Tue, 08 November 2005 22:50 |
Camira and Lada both have 111 tooth 19mm wide belt, but the lada has the correct type of ribs: as in round , camira has square. Lada timing belt gates- $34.00 [trade]from repco.
|
Mine was a Camira part and it had round ribs.
|
|
|
Location:
Brisbane
Registered:
May 2002
|
|
|
