Toymods Car Club Inc: Tech & Conversions => Qiuck shifter

Toymods Car Club
www.toymods.org.au

Toymods » Tech & Conversions » Qiuck shifter Show: Today's Posts :: Show Polls Email to friend

Author

Topic

Bluewire
Regular

Location:
Adelaide, South Oz
Registered:
May 2002

Qiuck shifter	Sun, 31 August 2003 00:40

Hey can you get a Qiuck shifter for a Celica 5 speed ? [Report message to a moderator]

mrshin
Forums Junkie

Location:
Montrose, VIC
Registered:
May 2002

Re: Qiuck shifter	Sun, 31 August 2003 07:17

Sure can - you can do what I did and make one It's really not that hard... [Report message to a moderator]

Location:
Adelaide
Registered:
August 2003

Re: Qiuck shifter	Sun, 31 August 2003 08:11

Could you explain how to make one? Is this for a manual box? Thanks, Tim [Report message to a moderator]

Cool1
Forums Junkie

I supported Toymods
Banned User

Location:
Brisbane
Registered:
May 2002

Re: Qiuck shifter	Sun, 31 August 2003 08:17

a quick shifter for an auto [Report message to a moderator]

Bugman
Forums Junkie

Location:
Sydney
Registered:
May 2002

Re: Qiuck shifter	Sun, 31 August 2003 08:19

yeah I hate my damn slow shifter. [Report message to a moderator]

I supported Toymods

Location:
Perth
Registered:
May 2002

Re: Qiuck shifter	Sun, 31 August 2003 08:19

Hehe, I was thinking it, but you had to say it [Report message to a moderator]

Bluewire
Regular

Location:
Adelaide, South Oz
Registered:
May 2002

Re: Qiuck shifter	Wed, 03 September 2003 09:04

So how do i do it...... please [Report message to a moderator]

Youngy
Forums Junkie

Location:
Eskilstuna, Sweden
Registered:
May 2002

Re: Qiuck shifter	Wed, 03 September 2003 09:22

If your familiar with what the gear stick and mount looks like out of the box this explanation will be of use. Ok the gear stick has a pivot point that will get bolted into the gear box by a kind of cup (four bolts). So you have a kind of basic ball and socket arrangement. Below this pivot point is a small section of the gear stick that generally tapers down to another ball - smaller and distinct form the pivot point. This smaller ball fits into a cup of the selectors in the gear box (they normally have a urethane clip sort of thing to hold them in the cup of the selector). You cut off this smaller ball below the pivot point and do so right on the ball thus leaving the taper part from the pivot point. Then you weld in an extension of say 10-15mm (open to speculation, you can have more if you want that true rally shift on the cheap) and weld the smaller ball onto this extension. Clean up the welds and thus the distance between pivot point and selector ball has been increased. The consequence of this is you have to make up a spacer in the shape of the cup\plate that holds it in the box. Like this sort of thing: and Cheers [Updated on: Wed, 03 September 2003 09:23] [Report message to a moderator]

hotrolla
Forums Junkie

Location:
Sydney
Registered:
April 2003

Re: Qiuck shifter	Wed, 03 September 2003 10:18

I would'nt mind doing that but iam to scared to do it [Report message to a moderator]

Steve M
Forums Junkie

Location:
Adelaide
Registered:
June 2003

Re: Qiuck shifter	Thu, 04 September 2003 00:14

That spacer looks pretty proffessional, did you make that too or are these available from shops. [Report message to a moderator]

omegaman
Regular

Location:
SYDNEY
Registered:
August 2003

Re: Qiuck shifter	Fri, 19 September 2003 00:45

There was a place in sydney/revesby that sold quick shifters for w series boxes. Dellow I think. You just needed to tell them what base plate pattern you had on the g/box eg. the pattern the gear stick plate which bolted to the box. [Report message to a moderator]

Previous Topic:	gearbox change
Next Topic:	Question about conversion

Current Time: Sun Jul 20 01:36:17 UTC 2025

Total time taken to generate the page: 0.0051231384277344 seconds

.:: Contact :: Home ::.