| Author | Topic |
|---|
Location:
ghetto area 2745
Registered:
November 2003
|
 thottle bodied 100kw
|
Wed, 26 November 2003 09:53
|
 |
 proffesionally built 100kw head ported and polished gas flowed trd cams trd pulleys trd valve springs head gasket cosworth pistons lightened and balanced crank all new bearings 20v quad throttle bodies 110mm trumpets 4into2into1 extractors and ems stinger wired to suit engine . this engine has only done 5000kms and ran a 1m16s at wakefield genuine reason for sale 4agte going into my sprinter offers around the 4 grand for the lot and it WILL NOT be split
|
|
|
Location:
ghetto area 2745
Registered:
November 2003
|
|
Re: thottle bodied 100kw
|
Wed, 26 November 2003 11:36
|
|
BUMP!!!!! has no one got any money these days ?????? 
|
|
|
Location:
camden
Registered:
September 2003
|
|
Re: thottle bodied 100kw
|
Wed, 26 November 2003 13:07
|
|
|
4 g's jesus christ....how much did you spend on it dude? cause i wanna do the same to my ge....
|
|
|
Location:
ghetto area 2745
Registered:
November 2003
|
|
Re: thottle bodied 100kw
|
Wed, 26 November 2003 22:19
|
|
|
the engine itself owes me about $6500 computer was a grand and the extractors were $380 all up 4 grand aint bad considering its only 5000kms old and it revs hard
|
|
|
Registered:
October 2003
|
|
Re: thottle bodied 100kw
|
Thu, 27 November 2003 00:07
|
|
|
can you tell me what specs on the cams are and who built the engine. Do you know the hp at rear wheels or flywheel ?
|
|
|
Banned user
Location:
ADELAIDE - The Drift City
Registered:
July 2002
|
|
Re: thottle bodied 100kw
|
Thu, 27 November 2003 01:04
|
|
also wanting to know cam specs and power at flywheel.
What compression ratio?
reasons for sale?
|
|
|
Location:
ghetto area 2745
Registered:
November 2003
|
|
Re: thottle bodied 100kw
|
Thu, 27 November 2003 01:35
|
|
|
engine was built by phil rhil dynoed by stuart wilkins rallying made 94kw at wheels cams not sure off will phone phil after a while reason for sale putting a turboed 4agze into my levin with celica 5 speed and hilux diff other wise i would not be parting with her
|
|
|
Location:
ghetto area 2745
Registered:
November 2003
|
 Re: thottle bodied 100kw
|
Thu, 27 November 2003 07:59
|
|
 BUMP BUMP BUMP!!!
|
|
|
Location:
Adelaide
Registered:
August 2003
|
|
Re: thottle bodied 100kw
|
Thu, 27 November 2003 08:29
|
|
honestly, i dont think anyone will buy that engine for 4grand..
4 grand..hmm..i can buy 2 sr20det engine..
nice
my advice..keep that engine..since u already choose to invest 6grand on that engine...keep it..
my 2cents
|
|
|
Location:
ghetto area 2745
Registered:
November 2003
|
|
Re: thottle bodied 100kw
|
Thu, 27 November 2003 09:05
|
|
|
you obviously have never built an engine before or read the add it comes with an computer on full exhaust as for putting a nissan engine in an AE86 you are just a dope
|
|
|
I supported Toymods
Location:
sydney.au
Registered:
August 2002
|
|
|
Location:
Adelaide
Registered:
August 2003
|
|
Re: thottle bodied 100kw
|
Thu, 27 November 2003 12:44
|
|
yes i've never built an engine before...  and i will never pay that much either if its 94kw on the wheel..
say me a dope if that makes u feel so much better..
|
|
|
Location:
Sydney
Registered:
May 2002
|
|
Re: thottle bodied 100kw
|
Fri, 28 November 2003 00:16
|
|
Satoshi,
94kw at the wheels is quite good for a normally aspirated 16v 4AG. This engine would probably be a good start for someone wanting to race in an under 1600cc category such as Improved Production and you would be surprised how much genuine racers are prepared to pay for good equipment.
If it's not your thing, go and buy a couple of SR's. Your 2 cents really is unnecessary.
SEXY 16,
Drop me a line at vicanddaz@hotmail.com with the full details such as cam specs, comp ratio etc and I'll pass it on to a few people I know that race 4AG's. It may be a little mild for them but you never know.
Darren.
|
|
|
Location:
ghetto area 2745
Registered:
November 2003
|
|
Re: thottle bodied 100kw
|
Fri, 28 November 2003 07:02
|
|
|
darren have to go out tonight will phone phil who built the engine and get full spec of everything probally tomorrow
|
|
|
Location:
Brisbane
Registered:
July 2003
|
|
Re: thottle bodied 100kw
|
Fri, 28 November 2003 23:14
|
|
SEXy 16,
could u post those spec here or e-mail me too, at klintthian@hotmail.com
|
|
|
Location:
ghetto area 2745
Registered:
November 2003
|
|
Re: thottle bodied 100kw
|
Sat, 29 November 2003 08:22
|
|
|
my engine= hi torque 4age 304 cams trd valve springs ported polished and gas flowed head cosworth pistons arp bolts lightened and balanced bottom end adjustable cam pullys 20valve quad throttle bodies 110mm trumpets 4-2-1 manifold 2 1/2 mandrel bent exhaust ems stinger computer wired to go engine done 5000kms since rebuild can rev to 9200rpms safe built by phil rhill at the start of the year open to any serious offers will be sold as a complete package any serious enquries phone 0425350015
|
|
|
Location:
Redbank Plains,near Ipswi...
Registered:
May 2002
|
|
Re: thottle bodied 100kw
|
Sun, 30 November 2003 21:27
|
|
|
for whats its worth, the cost of these engines is in the $5-$7k range, if built professionally. I build my own engines as I have access to all the gear, and parts alone cost $2500-$3500 for a good job (cams $500, pistons $900, gasket $200, bearings $200, oil pumo $200, bolts etc $300, balancing $300, etc etc). my personal experience however is used race engines only sell for a fraction of cost, no matter what brand they are r who built them. For the go-faster street kids, please dont bag people on this forum if you dont know or understand, just make polite comments or ask questions, and be prepared to learn something.
|
|
|
