| Author | Topic |
|---|
Registered:
February 2004
|
|
4agte Looking for advise and suggestions
|
Sat, 07 February 2004 05:18
|
 |
Hello All
Well, now that I have asked anuff questions for the shop now on to my own project.
The chassis is a 91 AE92 Prizm GSI (Chevy body/Toyota everything else)
Here in the states it was the only 4 DR w/ the 4ag motor in it.
Mine came BSE model so I did the full conversion myself like 4 years ago. After 3 good years out of the Blue Top (large port,TVIS) the motor finally let go. Now after it sit for a year I am getting ready to rebuild the motor and turbo it.
So far the list of Parts is:
SDS engine management/ MSD ignition
ACT Xtrem Pressure plate and street disc
HKS cast manifold for the AE86 (having to make a 1" adapter plate to make it bottom mount, so I can shut my hood w/ the turbo mounted)
Spearco Intercooler (front mount)
8:1 4AGZE pistons (20 over)
7 Rib high comp block
TVIS head
Greedy Type S blow off valve
Turbo off of the RB25
Full flow oil cooler
Oil filter relocation kit
ARP head studs, mains, rod bolts
TRD .7mm metal headgasket
255 Walbro Fuel pump
I was looking at getting some 450cc injectors out of a DSM Eclipse, but unsure if they will fit the Toyota head.
Is ther any w/ that flow rate that yall might suggest?
The gauges I am using are:
AutoMeter Electric
Boost, EGT, Oil Temp, Oil Pressure
So far this is all I have come up w/ minus the normal rebuild Parts that I am getting from the local Toyota dealer.
IS there anything yall can think of that I am missing or might need?
Any problems that anyone might have encountered that I should be aware of?
I know there are alot of good Toyota techs on this board this is why I have brought this to yall.
Thanks for you thoughts and suggestions.
Aaron
|
|
|
Location:
Montrose, VIC
Registered:
May 2002
|
|
Re: 4agte Looking for advise and suggestions
|
Sun, 08 February 2004 11:36
|
|
Sounds reasonable, only 2 things I'd change:
1. Rather than mess with adapters, just make a manifold that fits the job
2. That yank accent 
|
|
|
Location:
Montrose, VIC
Registered:
May 2002
|
|
|
Location:
NSW, East Coast
Registered:
July 2003
|
|
Re: 4agte Looking for advise and suggestions
|
Sun, 08 February 2004 11:56
|
|
Would be a good idea to do the rods while your at it.
It would suck big time if one let go.
Sounds like its all in place thou.
|
|
|
Registered:
February 2004
|
|
Re: 4agte Looking for advise and suggestions
|
Sun, 08 February 2004 18:51
|
|
Thanks for the replies guys.
What's wrong Mrshin don't like my yank accent? ha ha ha!! 
I know this guy here in VA running the GZE injectors in his AE86 w/ A Turbonetics T3 but his duty cycle is a little high. That's why I was looking at the 450cc's. Plus w/ the SDS I can pulse them down anuff so that it will idle good. Hell the guys at the shop where trying to get me to run 550's, but I thought that was a little to much myself.
I was under the impression that the rods in the High comp block and the GZE were the same. I dunno? 
|
|
|
I supported Toymods
Location:
Northern Beaches
Registered:
May 2002
|
|
Re: 4agte Looking for advise and suggestions
|
Sun, 08 February 2004 20:16
|
|
Ones out of a 7m-gte will go straight in, I think they are 450cc?
Not sure if you got that motor out there in anything?
and yea im with mr shin and the accent hehe
|
|
|
Location:
Montrose, VIC
Registered:
May 2002
|
|
Re: 4agte Looking for advise and suggestions
|
Wed, 11 February 2004 22:41
|
|
|
Gotta speak with a bit of Ozzie Draaaaawl..... NOT like Cleetus!
|
|
|
