Toymods Car Club
www.toymods.org.au
F.A.Q. F.A.Q.    Register Register    Login Login    Home Home
Members Members    Search Search
Toymods » Tech & Conversions » RA23 brakes setup in TA22

Show: Today's Posts  :: Show Polls 
Email to friend 
Switch to threaded view of this topic Create a new topic Submit Reply
AuthorTopic
fade-e
Forums Junkie


Location:
Sydney
Registered:
June 2004
icon5.gif  RA23 brakes setup in TA22 Mon, 14 June 2004 06:35 Go to next message
hey guys!

please forgive my ignorance or any other stupidity that i may have Embarassed , i have done searches and the amount of info is amazing yet making my eues and brain hurt... so my Q is this...

i have been offered both sides, front vented discs, complete strut house, not sure if comes with calipers, no shock or springs... though i have TA22 shocks, and both standard springs and 2" lowered springs

the front suspension setup comes from an RA23, would this go into the TA22 directly? if not what headache will i have to be prepared for? and can i use my shocks and springs?
  Send a private message to this user    
fade-e
Forums Junkie


Location:
Sydney
Registered:
June 2004
Re: RA23 brakes setup in TA22 Mon, 14 June 2004 06:38 Go to previous messageGo to next message
Embarassed Embarassed Embarassed Embarassed

i am so stupid... just saw the articles section now Very Happy but any info bout the RA23 setup will still be good... that way i cn tell the person whether i want them or not
  Send a private message to this user    
thetoyman75
Forums Junkie


Club President
I supported Toymods

Location:
Sydney
Registered:
May 2002
 
Re: RA23 brakes setup in TA22 Mon, 14 June 2004 12:14 Go to previous messageGo to next message
Fade-e,

The TA22 Struts are shorter thanthe RA23 units. Depending on how they have been set up you may find they raise the front of your car an inch or so.

  Send a private message to this user    
fade-e
Forums Junkie


Location:
Sydney
Registered:
June 2004
Re: RA23 brakes setup in TA22 Mon, 14 June 2004 12:26 Go to previous messageGo to next message
are the springs the same though? cause i got 2" lowered springs... if they fit and raises the car an inch then the grinder can come out for that inch to even the front and rear again...

but are they the same springs???
  Send a private message to this user    
fade-e
Forums Junkie


Location:
Sydney
Registered:
June 2004
icon5.gif  Re: RA23 brakes setup in TA22 Mon, 14 June 2004 14:12 Go to previous message
further to my last post, i remember reading i think its ryans page (the guy in america running the 10s) when he did the front brake conversion he added like an invh to the lower control arm to compensate for camber...

keeping that in mind, than theoretically i would believe it possible to cut the strut/shock housing by an inch???

guys any ideas on this theory of mine??????????????
  Send a private message to this user    
  Switch to threaded view of this topic Create a new topic Submit Reply
Previous Topic:1UZ Crown wiring diagram
Next Topic:wut do you think of these modern audi motor ideas ?
Goto Forum:
-=] Back to Top [=-

Current Time: Mon Jul 28 02:59:49 UTC 2025

Total time taken to generate the page: 0.0037851333618164 seconds

Bandwidth utilization bar

.:: Contact :: Home ::.

Powered by: FUDforum 2.3.8
Copyright ©2001-2003 Advanced Internet Designs Inc.