| Author | Topic |
|---|
Location:
PNG
Registered:
June 2002
|
|
|
Location:
Sydney
Registered:
May 2002
|
|
Re: Craig's ta23
|
Thu, 19 September 2002 10:34
 
|
 |
F**KN sweet
|
|
|
I supported Toymods
Toymods Club Secretary
Location:
Sydney
Registered:
May 2002
|
|
Re: Craig's ta23
|
Thu, 19 September 2002 22:41
|
|
aaaah yes... I remember this little beast from down at Wakefield last December.. Absolutely beautiful! 
Was funny watching it go out on the track with the roof-racks on though!! 
|
|
|
Toymods Board Member
I supported Toymods
Location:
Turramurra, Sydney.
Registered:
May 2002
|
|
Re: Craig's ta23
|
Fri, 20 September 2002 06:30
|
|
Mmmmm, that does look sweet.
And finally someone else with painted bumpers, good work!
|
|
|
I supported Toymods
Location:
south of the big smoke
Registered:
May 2002
|
|
Re: Craig's ta23
|
Tue, 24 September 2002 21:21
|
|
im in love!!! thats to nice to drive around the farm
give it to me!!!
car looks good man
|
|
|
Location:
canberra
Registered:
August 2002
|
|
Re: Craig's ta23
|
Fri, 08 November 2002 06:17
|
|
|
Got my answer to the previous question! And yes, it is sweet!
|
|
|
Club Member
Location:
Sydney, NSW
Registered:
May 2002
|
|
Re: Craig's ta23
|
Sun, 10 November 2002 13:13
|
|
Looks nice...
A lot of work too...
|
|
|
I supported Toymods
Location:
south of the big smoke
Registered:
May 2002
|
|
Re: Craig's ta23
|
Tue, 03 June 2003 06:07
|
|
hey craig u wouldnt happen to have the diagram for the factory tacho would ya?
i did the same thing as you but havent had chance to wire it up
cheers
|
|
|
I supported Toymods
Location:
NE Melbourne
Registered:
May 2002
|
|
Re: Craig's ta23
|
Mon, 16 June 2003 13:58
|
|
|
painted bumpers??? are you kidding... i'm a huge fan of chrome!!!
|
|
|
Location:
PNG
Registered:
June 2002
|
|
Re: Craig's ta23
|
Fri, 17 September 2004 01:49
|
|
The car has had an upgrade since last post.
Engine
1GGTEU from 1989 Manual Supra (GA70)
Garret GT25 8004 .64 tirbine .8 TO4s compressor
(sometimes called a GT28)
modified inlet manifold
EB ford throttle body (and idle control)
7MGTE 440cc injectors
EL falcon 6 coil pack
HKS single turbo exhaust manifold
3 in dump pipe with seperate plumbing for wastegate
3in hi flow cat
The drops to 2.5 in, Resonator, turbo muffler
450x300x76 intercooler
Three core radiator 14” Electric fan
Celimad booster adjuster (14lb)
Microtech Lx8 (modified for ford idle control)
Precision INJECTION 1.5Lt Surge tank
Malory prepump
Bosch motorsport fuel pump
5/16 fuel line
Transmission
Lightened billet flywheel (TRD)
TRD coverplate
Button clutch (5 paddle)
VH44 remote booster for clutch
j160 6 speed gearbox
RT104 tailshaft
F series 7.5inch lsd in Mk2 Corona banjo case
Front Brakes
Hilux 4WD LN106 4 piston calipers
Pagid Pads
Peugeot 11inch Rotors
GA70 Master Cylinder
PBR Brake Bias Adjuster
Rear Brakes
RT141 disk brake and hand brake assembly
Bendix pads
Front Suspension
RT132 struts
Strut tower adjustment plate (camber/caster)
Coil overs 60mm
Sway bar (20mm) of unknown origin
Koni adjustable inserts
35mm RCA
Rear Suspension
King 32mm progressive rate springs
Koni adjustable shocks
Whiteline adjustable sway bar (20mm)
Whiteline adjustable Panard Rod
Adjustable upper control arms
Wheels and Tyres
15 X 7 ROH wheels
Bridgestone Front 195x50 Potensa
Rear 225x45 530s
Interior
Honda Prelude (imported) front seats
Interior replaced (with back seats retained but recovered)
Formuling 14in Steering Wheel
Speco fuel, oil pressure and temperature gauges filling the 3 holes
Spitfire boost pressure gauge
GA70 Tacho, including boost light, filling the factory tacho assembly
FET turbo timer
Kenwood CD
Fire extinguisher
Other
Upgraded headlights
Cruise
Remote keyless entry
And of course the roof racks
Car initially dyno'ed at 200 rear wheel kilowatts at 13psi. Will pump it up to 18-20 psi in the next few weeks
|
|
|
Location:
Carlingford, Sydney
Registered:
May 2002
|
|
Re: Craig's ta23
|
Sun, 10 October 2004 03:33
|
|
man thats on tuff 1g
any chance of a dyno printout?
|
|
|
