| Author | Topic |
|---|
Location:
Toowoomba
Registered:
May 2002
|
 Last Call, RA23 parts must go
|
Fri, 31 May 2002 01:12
|
 |
|
some stuff will only cost you postage. I have all supsension, panels and stuff, not much interior there, no drivetrain (engine, gb, tailshaft, diff center). I'm selling it to the wreckers in about two weeks so if you need anything at all let me know.
|
|
|
Location:
Brisbane
Registered:
May 2002
|
|
Re: Last Call, RA23 parts must go
|
Mon, 03 June 2002 01:50
|
|
Hey, i'm still interested in the shell, with some of the parts.................. I sent you emails about it last week.
Just got to figure out how I'm going to get it from Toowoomba to Brisbane!!
|
|
|
Location:
Toowoomba
Registered:
May 2002
|
|
Re: Last Call, RA23 parts must go
|
Mon, 03 June 2002 02:44
|
|
hehe, it is towable but I'd be cautious towing it that far and down the range (hehe  ). A flat bed car trailer can be hired farily cheaply and I'll take that into consideration when I work out what it's worth. Celicamad has seen the car and there were more bits he hadn't seen too. Get back to me when you find out how you want to transport it and i'll get you some photos if you like (not much to look at). I can promise you it will be cheap.
|
|
|
Banned member
Location:
Brisbane
Registered:
May 2002
|
|
Re: Last Call, RA23 parts must go
|
Sun, 23 June 2002 09:36
|
|
yeah its definatly worth fixing the shell looked good, not sure about what parts are missing, it would have been a nice car in its former life (prior wrecking)
will can i grab those hinges off you soon mate ?
|
|
|
Location:
Brisbane
Registered:
May 2002
|
|
Re: Last Call, RA23 parts must go
|
Sun, 23 June 2002 10:30
|
|
have you got a passenger side mirror?
oh and will it fit a ta22?
|
|
|
Location:
Toowoomba
Registered:
May 2002
|
|
Re: Last Call, RA23 parts must go
|
Sun, 23 June 2002 13:30
|
|
|
sorry, no passenger side mirror unless it's buried under other parts. I have a drivers one that look very crappy. I think the car has been taken anyhow, a project race car for someone. I hope he gives me a drive when it's done. So no more parts unless he doesn't take it. (he should, it's free)
|
|
|
Location:
Sunshine Coast
Registered:
September 2002
|
|
Re: Last Call, RA23 parts must go
|
Sun, 08 December 2002 09:02
|
|
Hows the dash looking and what colour??
also the rear bumper condition? any rust in doors and boot?
|
|
|
Location:
Toowoomba
Registered:
May 2002
|
|
Re: Last Call, RA23 parts must go
|
Sun, 08 December 2002 09:42
|
|
|
No Message Body
|
|
|
Location:
Toowoomba
Registered:
May 2002
|
|
Re: Last Call, RA23 parts must go
|
Sun, 08 December 2002 09:45
|
|
|
sorry, car went a very long time ago. I do however have a spare dash that i'm currently using to make a fiberglass mould of. Mould is still some way off but once i'm finished i'll have no troubles parting with whats left. It's all useable but not in very good nik. The gauge panel (2 of) are very good though. I have a dinted front bumper but no rear. I can get photos if anyone wants it. I also have a set of door hinges (both sides) and bonnet hinges (both of them) and some other misc. stuff that I will be sorting out soon. No panels or anything like that, just bits from here and there. I'll list em later.
|
|
|
Location:
Sunshine Coast
Registered:
September 2002
|
|
Re: Last Call, RA23 parts must go
|
Mon, 09 December 2002 02:22
|
|
|
Yeah send me pics of whateva you have i might be able to use them in my new project.
|
|
|
Location:
NSW
Registered:
May 2002
|
|
Re: Last Call, RA23 parts must go
|
Mon, 09 December 2002 03:21
|
|
Dude,
How good are the bonnet hinges?? And how much do you want for them?? Mine are rooted....let me know
|
|
|
Location:
Ipswich
Registered:
May 2002
|
|
Re: Last Call, RA23 parts must go
|
Wed, 08 January 2003 13:51
|
|
|
I'm guessing I'm WAAAAY late in replying, but do you have a fuel/temp gauge?
|
|
|
Location:
Toowoomba
Registered:
May 2002
|
|
Re: Last Call, RA23 parts must go
|
Wed, 08 January 2003 14:21
|
|
|
Actually I do. We'll the internals that is, the circuit board is had it. Not sure if the internals are any good but you are welcome to them at no charge if you want. Do you ever come up to toowoomba? Or I could send them down with my sis next week some time. BTW, do you know of any jobs going around the brisbane area, my sister is looking for work and I thought i'd give her a hand to look.
|
|
|
Location:
Ipswich
Registered:
May 2002
|
|
Re: Last Call, RA23 parts must go
|
Wed, 08 January 2003 17:10
|
|
What do you mean by "the internals that is, the circuit board is had it"?
I just need the actual gauge itself, working of course. Don't need the housing or the printed circuit board or anything, I'm custom mounting it in my KE55. Similar to what Jonny has done in his KE55
I don't generally go up to Toowoomba, if your sister is coming over here it would be great, I could meet her up somewhere and get it off her (assuming they do work?).
Umm... Jobs... I don't really know of any jobs going at the moment, but what field is your sister looking into? If you let me know I'll keep my eye out.
|
|
|
Location:
Toowoomba
Registered:
May 2002
|
|
Re: Last Call, RA23 parts must go
|
Wed, 08 January 2003 23:25
|
|
|
I'll see if I can test it somehow and give it to her later on next week.
|
|
|
Location:
Ipswich
Registered:
May 2002
|
|
Re: Last Call, RA23 parts must go
|
Thu, 09 January 2003 00:03
|
|
Hmm, I have no idea how to test it either... If you're not sure if it works or not I'll take it anyway, and if it works then all is good, if it doesn't then well... I'll just have to look for another one 
Thanks
|
|
|
