| Author | Topic |
|---|
On Probation
Location:
nsw
Registered:
March 2004
|
|
1GGTE Bottom end
|
Mon, 04 July 2005 06:08
|
 |
What parts am i gunna need to rebuild it 
|
|
|
I supported Toymods
Location:
Australia
Registered:
November 2003
|
|
Re: 1GGTE Bottom end
|
Mon, 04 July 2005 06:41
|
|
Depends whats fucked.
Bearings at a minimum. Crank may need fixing if you have scored it.
Rings you may as well.
Bores may need honing, then bigger pistons may be required if bored out to much.
Plus all the obligatory seals and gaskets.
|
|
|
On Probation
Location:
nsw
Registered:
March 2004
|
|
Re: 1GGTE Bottom end
|
Mon, 04 July 2005 06:49
|
|
|
I think its honed allready all i really was thinking of doing was the crank bearings?
|
|
|
I supported Toymods
Location:
Australia
Registered:
November 2003
|
|
Re: 1GGTE Bottom end
|
Mon, 04 July 2005 06:51
|
|
|
If you are leaving the pistons in there, just do big end bearings and mains bearings.
|
|
|
On Probation
Location:
nsw
Registered:
March 2004
|
|
Re: 1GGTE Bottom end
|
Tue, 05 July 2005 22:43
|
|
|
Thanks Cruz If the big end bearing is worn more on one side than the other does that mean the cranks oval ? if so can i get away with just replacing the centre cap bearings?
|
|
|
I supported Toymods
Location:
Australia
Registered:
November 2003
|
|
Re: 1GGTE Bottom end
|
Wed, 06 July 2005 00:34
|
|
Dunno dude.
Get it checked out.
|
|
|
On Probation
Location:
nsw
Registered:
March 2004
|
|
Re: 1GGTE Bottom end
|
Wed, 06 July 2005 06:32
|
|
Anyone got a good one they dont want  does it matter what gen it is 2 or 3 ?
|
|
|
Location:
Arthurs Creek, Victoria
Registered:
May 2002
|
|
Re: 1GGTE Bottom end
|
Thu, 07 July 2005 01:36
|
|
I do happen to have a 1g crank, it's gen 3, but I'm kinda attached to it, so it wouldn't go cheap.
|
|
|
On Probation
Location:
nsw
Registered:
March 2004
|
|
Re: 1GGTE Bottom end
|
Thu, 07 July 2005 01:51
|
|
How did you get attached you know your not ment to put things in your bum  thanks but Im looking for a whole bottom end
|
|
|
Location:
Arthurs Creek, Victoria
Registered:
May 2002
|
|
Re: 1GGTE Bottom end
|
Thu, 07 July 2005 02:16
|
|
Well, I have the whole engine, so if I'm selling the crank, the ancillaries could go with it. And I know they're in good nick.
|
|
|
On Probation
Location:
nsw
Registered:
March 2004
|
|
Re: 1GGTE Bottom end
|
Tue, 12 July 2005 03:43
|
|
|
Anyone know where to get a cheap bottom end rebuild kit ie rings/crank bearings/main seals ?
|
|
|
Location:
sunny coast, qld
Registered:
October 2002
|
|
Re: 1GGTE Bottom end
|
Tue, 12 July 2005 03:57
|
|
|
I also have a 1g parts engine that is in good nick AFAIK. If you need any bits, let me know.
|
|
|
On Probation
Location:
nsw
Registered:
March 2004
|
|
Re: 1GGTE Bottom end
|
Tue, 12 July 2005 04:01
|
|
|
What gen ?
|
|
|
Location:
sunny coast, qld
Registered:
October 2002
|
|
Re: 1GGTE Bottom end
|
Tue, 12 July 2005 04:17
|
|
don't know? was out of 87 gz20.
Personally I can't see there being any differences internally between gen 1,2 or 3.
|
|
|
On Probation
Location:
nsw
Registered:
March 2004
|
|
Re: 1GGTE Bottom end
|
Tue, 12 July 2005 05:19
|
|
PM Sent
|
|
|
