| Author | Topic | 
|---|
|  
 Location:
 Melbourne
 Registered:
 November 2003
 
 | 
	| Dyno Day - 10th September - Beninca Dyno |  Mon, 22 August 2005 04:58   |  |  |  
	| Okay here is the new thread with all the info up the top for everyone. I've also taken it as Adrian can't get online much these days. 
 Where
 Beninca Automotive
 581 Canterbury Rd
 Surrey Hills
 
 Map at bottom of page.
 
 When
 10th September 2005
 FWD: Starting 10:00am
 RWD: Starting at 12:00pm
 AWD: Starting at 4:30pm
 
 Note: If you are not there on time your slot may be given to someone else and you may not get on the dyno.
 
 Cost
 $20 for Front and Rear Wheel Drives
 $25 for All Wheel Drives
 
 No deposit required, pay on the day.
 
 Includes
 > Speedo check at 100km/h
 > A/F ratios
 > Power and torque curve
 > Peak power and torque @ RPM
 (if you came to the last dyno day, it'll be the same)
 
 Teh BBQ!
 There will be a BBQ on the day, this will include:
 > Soft Drinks of various flavours
 > Snags
 > Onions
 > BBQ/Tomato sauce + mustard
 > Perhaps some tofu for the spoontah boys.
  > Bread
 There will be a charge for all the above stuff, but it wont be much.
 If you want anything else to be cooked, bring it along and we'll chuck it on the BBQ.
 
 Dyno stats
 Total power capacity 900Kw. Higher in ramp phase
 Max speed 250kph
 18Kw centrifugal double rotor-cooling fan. External to cell for maximum test area.
 Sound proof cell.
 Longitudinal ventilation with noise attenuation on air exit.
 Atmospheric corrected power temperature, humidity and barometric pressure
 Ramp, steady state, ECU mapping, kms travelled functions
 Data stream IN and OUT from dyno PC to correlate data from vehicle ECU (Autronic data stream) OBD and other communication protocols in future.
 2.1 to 4.15 meter wheelbase. ( Ford F350 158 inch wheel base )
 Wireless hand control
 A/F ratio input, thermocouples, pressures, etc
 Compare data functions
 Large screen oscilloscope 400mm for ignition and knock pattern display.
 
 The list is now full. Now taking reserves...
 If you want to rock up anyway, you're more than welcome to, if there's space, we will chuck you on the rollers.
 
 Map:
 Parking on Stirling Crescent.
 
   [Updated on: Tue, 13 September 2005 01:24]
	
	 |  | 
|  | 
|  
 Location:
 Melbourne
 Registered:
 November 2003
 
 |  | 
|  | 
|  
 Location:
 Melbourne, Australia
 Registered:
 March 2005
 |  | 
|  | 
| 
 Location:
 melbourne
 Registered:
 November 2003
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Mon, 22 August 2005 05:28    |  |  |  
	| how do we make our deposits? |  | 
|  | 
|  
 Location:
 Melbourne
 Registered:
 November 2003
 
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Mon, 22 August 2005 05:50    |  |  |  
	| If we get a few more people there may not be a need for a deposit. 
 I'll keep you guys posted.
 |  | 
|  | 
| 
 Location:
 melbourne
 Registered:
 November 2003
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Mon, 22 August 2005 06:01    |  |  |  
	| oh k, i didnt know we needed more people. i cant get some others who are interested, will report back.
 |  | 
|  | 
|  
 Location:
 Melbourne
 Registered:
 November 2003
 
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Mon, 22 August 2005 06:16    |  |  |  
	| Don't NEED more, but if we get some more, then there wont be any need for a deposit. Otherwise yeah, I have a paypall account (I think it still works) or you can netbank it over to me (I'm with commonwealth). But first lets see if we can get a few more so we don't need a deposit. |  | 
|  | 
|  
 Location:
 Melbourne
 Registered:
 May 2002
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Mon, 22 August 2005 07:11    |  |  |  
	| Name: Grant Forum: Toymods
 Car: Toyota Sprinter
 Engine: 4AGE
 Power: 72 rwkw!
 
 
 |  | 
|  | 
|  
 I Supported Toymods
 
 Location:
 Lwr Templestowe, Melbourne
 Registered:
 August 2004
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Mon, 22 August 2005 08:03    |  |  |  
	| Don't forget me 
 Name: Yian
 Forum: Toymods
 Car: Not a sprinter
 Engine: Not a 4age
 Power: More than 100rwkw
 
 Like I mentioned before, if you need more people, 2 of my workmates want to come.
 |  | 
|  | 
|  
 Location:
 Melbourne - NthSubs
 Registered:
 January 2004
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Mon, 22 August 2005 08:19    |  |  |  
	| Name: leo Forum: Toymods
 Car: ae95 4wd corolla
 Engine: 4afe
 Power: 7.4kw on each wheels
 |  | 
|  | 
|  
 Location:
 Melbourne
 Registered:
 November 2003
 
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Mon, 22 August 2005 08:24    |  |  |  
	| | Yian wrote on Mon, 22 August 2005 18:03 |  | Don't forget me
 
 Name: Yian
 Forum: Toymods
 Car: Not a sprinter
 Engine: Not a 4age
 Power: More than 100rwkw
 
 Like I mentioned before, if you need more people, 2 of my workmates want to come.
 
 | 
 Sorry about that, you're in there now.
 
 I think toymods members have had enough time to sign up for this. If you have anyone who'll definatly come, put 'em down here and I'll add them to the list.
 |  | 
|  | 
|  
 Location:
 Melbourne - NthSubs
 Registered:
 January 2004
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Mon, 22 August 2005 08:26    |  |  |  
	| can i change cars? say if i get my sprinter running can i bring that insted of the pos wagon of doom? |  | 
|  | 
|  
 Location:
 Melbourne
 Registered:
 November 2003
 
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Mon, 22 August 2005 08:31    |  |  |  
	| | rthy wrote on Mon, 22 August 2005 18:26 |  | can i change cars? say if i get my sprinter running can i bring that insted of the pos wagon of doom?
 
 | 
 Sure can, but you'll have to make sure you're there early to slot in before the machine is re-set from RWD to AWD.
 |  | 
|  | 
|  
 Location:
 Melbourne - NthSubs
 Registered:
 January 2004
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Mon, 22 August 2005 09:04    |  |  |  
	| kool |  | 
|  | 
|  
 Location:
 Ballarat, Victoria
 Registered:
 March 2003
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Mon, 22 August 2005 11:02    |  |  |  
	| or me! 
 name: ryley
 forum: toymods
 car: supra
 engine: 7mgte
 power: hoping for 140rwkw
 |  | 
|  | 
|  
 Location:
 Melbourne
 Registered:
 November 2004
 
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Mon, 22 August 2005 11:28    |  |  |  
	| just wondering if they have a quarter mile reading with the dyno????? 
 i saw some dyno have em???????
 |  | 
|  | 
|  
 Location:
 Melbourne
 Registered:
 May 2002
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Mon, 22 August 2005 13:18    |  |  |  
	| Hey I'm also posting for a mate, who has a 180sx.. if he dosen't come it wont be fun! so he has to okay!  
 name: Jake
 forum: Friend!
 car: 180sx
 engine: SR20DET
 power: 130rwkw 200 with stickers
 
 if you guys are exclusionist snobs and don't want him to go just let me know
  
 Grant.
 |  | 
|  | 
|  
 Location:
 Melbourne
 Registered:
 May 2002
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Mon, 22 August 2005 13:28    |  |  |  
	| Okay also posting for! 
 name: Ying rocks!
 forum: Friend! (kinda toymods?)
 car: Starlet GT
 engine: 4EFTE
 power: 80fwkw 0rwkw
 
 
 |  | 
|  | 
|  
 Location:
 Melbourne
 Registered:
 November 2003
 
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Mon, 22 August 2005 13:39    |  |  |  
	| | Evil_Foetus wrote on Mon, 22 August 2005 21:02 |  | or me!
 
 name: ryley
 forum: toymods
 car: supra
 engine: 7mgte
 power: hoping for 140rwkw
 
 | 
 You're allready on there!
 
 
 | wolverine wrote on Mon, 22 August 2005 21:28 |  | just wondering if they have a quarter mile reading with the dyno?????
 
 i saw some dyno have em???????
 
 | 
 Nope. I'll call them and have specifics soon.
 |  | 
|  | 
|  
 I Supported Toymods
 
 Location:
 south Melbourne/KL
 Registered:
 June 2004
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Mon, 22 August 2005 16:16    |  |  |  
	| can i bring 2 cars?? i might bring my hsemates car as well |  | 
|  | 
|  
 Location:
 Melbourne
 Registered:
 November 2003
 
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Tue, 23 August 2005 00:47    |  |  |  
	| | b1gb3n wrote on Tue, 23 August 2005 02:16 |  | can i bring 2 cars?? i might bring my hsemates car as well
 
 | 
 Yeah sure, your housemate can come too if he likes.
   |  | 
|  | 
|  
 Location:
 Melbourne
 Registered:
 May 2004
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Tue, 23 August 2005 02:20    |  |  |  
	| I see a common trend here.. Let me help you all out. 
 YES! You can bring your car. (it would help with getting a dyno reading)
   
 YES! You can bring ya friends. (if they bring their car, even better)
   
 YES! The more the merrier. (I'm sure the dyno guys wont mind an extra $20 - $25 hear or there)
   
 So keep them confirmation posts rollin' in.
 
 |  | 
|  | 
|  
 I Supported Toymods
 
 Location:
 south Melbourne/KL
 Registered:
 June 2004
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Tue, 23 August 2005 03:50    |  |  |  
	| | ROME_GT4 wrote on Tue, 23 August 2005 12:20 |  | I see a common trend here.. Let me help you all out.
 
 YES! You can bring your car. (it would help with getting a dyno reading)
   
 YES! You can bring ya friends. (if they bring their car, even better)
   
 YES! The more the merrier. (I'm sure the dyno guys wont mind an extra $20 - $25 hear or there)
   
 So keep them confirmation posts rollin' in.
 
 
 | 
 YES! you can bring all the hot chicks too
   |  | 
|  | 
|  
 I Supported Toymods
 
 Location:
 Lwr Templestowe, Melbourne
 Registered:
 August 2004
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Tue, 23 August 2005 03:51    |  |  |  
	| *perks ear* Did someone say hot chicks? 
 Where where? *looks around frantically*
 |  | 
|  | 
|  
 I Supported Toymods
 
 Location:
 south Melbourne/KL
 Registered:
 June 2004
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Tue, 23 August 2005 03:54    |  |  |  
	| | Yian wrote on Tue, 23 August 2005 13:51 |  | *perks ear* Did someone say hot chicks?
 
 Where where? *looks around frantically*
 
 | 
 i'm sure NIM can work something out
   |  | 
|  | 
|  
 Location:
 S.E Melbourne
 Registered:
 May 2003
 
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Tue, 23 August 2005 09:45    |  |  |  
	| Do we get the air fuel ratios on the print out of our dyno sheet (ie do they stick the air sniffer up the zorst during the run)? |  | 
|  | 
|  
 Location:
 Melbourne, Australia
 Registered:
 March 2005
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Tue, 23 August 2005 09:48    |  |  |  
	| | XPLOSV wrote on Tue, 23 August 2005 19:45 |  | Do we get the air fuel ratios on the print out of our dyno sheet (ie do they stick the air sniffer up the zorst during the run)?
 
 | 
 
 Also interested in the answer to this question.  Happy to pay extra but don't want to disrupt proceedings.
 
 |  | 
|  | 
| 
 Location:
 Vic
 Registered:
 April 2004
 
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Tue, 23 August 2005 11:57    |  |  |  
	| Is it too late to get in on this? If i have time to whip out to Toyospares and back again by the time the AWD's are running i'll swing by. Using the stock ST205 figures and 25% drivetrain loss i should be getting about 130-140awk but it only seems to want to run about 7psi. 
 *shrugs*
 |  | 
|  | 
| 
 Registered:
 August 2005
 
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Tue, 23 August 2005 13:12    |  |  |  
	| are non-toyota's welcome?  i'm keen to see the 1jz cressida, and a mate's in love with AE68's and Gen 2 supra's.
 
 if its ok put us on the list.
 
 Name: John
 Forum: Toymods
 Car: EF Falcon GLi
 Engine: 4.0L I6
 Power: unknown
 
 Name: Mick
 Forum: Friend
 Car: EA/ED Falcon hybrid
 Engine: 3.9L
 Power: unknown
 |  | 
|  | 
|  
 I Supported Toymods
 
 Location:
 south Melbourne/KL
 Registered:
 June 2004
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Tue, 23 August 2005 13:44    |  |  |  
	| | XPLOSV wrote on Tue, 23 August 2005 19:45 |  | Do we get the air fuel ratios on the print out of our dyno sheet (ie do they stick the air sniffer up the zorst during the run)?
 
 | 
 they did the last time. also gave speedo reading at 100km/h compared to actual speed
 |  | 
|  | 
|  
 I Supported Toymods
 
 Location:
 Lwr Templestowe, Melbourne
 Registered:
 August 2004
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Tue, 23 August 2005 15:13    |  |  |  
	| | EFFalcon wrote on Tue, 23 August 2005 23:12 |  | )
 i'm keen to see the 1jz cressida, and a mate's in love with AE68's and Gen 2 supra's.
 
 
 | 
 
 Your mate will be in for a treat then
  Should be a couple of mid to high powered cressidas and mkII Supras. |  | 
|  | 
|  
 Location:
 S.E Melbourne
 Registered:
 May 2003
 
 |  | 
|  | 
|  
 Location:
 Melbourne
 Registered:
 November 2003
 
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Wed, 24 August 2005 04:12    |  |  |  
	| I'm yet to ring them, but with 35+ people we wont have time to do A/F ratios. I'll confirm this later, but speed check at 100, power and torque curve with peak power and peak torque @ RPM should be shown. I'll call 'em. 
 And Ben, don't have time to organise hot chicks! To much to do!
   |  | 
|  | 
| 
 I supported Toymods
 
 Location:
 Melbourne Australia
 Registered:
 November 2003
 
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Wed, 24 August 2005 05:22    |  |  |  
	| I dont see how an A/F Ratio reading would take longer to do, both times i've been there, no matter how many cars, there is a print out of the A/F ratio. speed check is done with calibration of the dyno for your respective run. |  | 
|  | 
|  
 Location:
 Melbourne
 Registered:
 November 2003
 
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Wed, 24 August 2005 06:23    |  |  |  
	| | da_horse wrote on Wed, 24 August 2005 15:22 |  | I dont see how an A/F Ratio reading would take longer to do, both times i've been there, no matter how many cars, there is a print out of the A/F ratio. speed check is done with calibration of the dyno for your respective run.
 
 | 
 I imagine they have to hook up the thingo to the tail pipe, which takes time. I'll ask.
 |  | 
|  | 
|  
 Location:
 Melbourne
 Registered:
 November 2003
 
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Wed, 24 August 2005 06:35    |  |  |  
	| Just rang 'em. 
 > A/F ratio is included
 > Speedo check at 100km/h
 > Power and torque curve
 > Peak power and torque @ RPM
 
 I'll post this at the top too.
 |  | 
|  | 
|  
 Location:
 Melbourne
 Registered:
 May 2002
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Wed, 24 August 2005 07:29    |  |  |  
	| Wow im actually getting excited! This should be fun   
 Hope to meet a few people there.
 
 Grant.
 |  | 
|  | 
|  
 Location:
 Melbourne
 Registered:
 November 2003
 
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Wed, 24 August 2005 08:29    |  |  |  
	| | fOOZ86 wrote on Wed, 24 August 2005 17:29 |  | Wow im actually getting excited! This should be fun
   
 Hope to meet a few people there.
 
 Grant.
 
 | 
 Naw, you wont. We'll be blindfolding everyone so there will be NO SOCIALISING!
   
 
   
 Naw should be good.
 Anyone interesting in organising the BBQ? I don't have a portible one. Might organise a pizza run or something on the day if nobody has a bbq to bring.
 |  | 
|  | 
|  
 Location:
 S.E Melbourne
 Registered:
 May 2003
 
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Wed, 24 August 2005 11:53    |  |  |  
	| Ok, I'm confirmed then. Is there still room? 
 Name: XPLOSV
 Forum: AUstarletClub
 Car: Starlet GT
 Engine: 1.3lt turbo
 Power: Never had it ona dyno but hope for around the 100hp mark (kinda conservative actually).
 |  | 
|  | 
| 
 Registered:
 August 2005
 
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Wed, 24 August 2005 23:11    |  |  |  
	| me me, I want to go too   
 
 Name: David
 Forum: AUstarletClub
 Car: Starlet GT
 Engine: 4e-fte
 Power: think around 70FWKW, 0RWKW
 
 
 |  | 
|  | 
|  
 Location:
 Melbourne
 Registered:
 November 2003
 
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Thu, 25 August 2005 05:59    |  |  |  
	| Okay, we're full! 
 For all those who missed a confirmed spot, I'm not making a list of reserves. If some people drop out or we have a gap while we wait for someone, we'll chuck the rerves on. First in, best dressed.
 
 Keep posting for the reserves people.
 |  | 
|  | 
|  
 Location:
 Colac, Victoria
 Registered:
 May 2002
 
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Thu, 25 August 2005 10:50    |  |  |  
	| id put a reserve in nim , but wont just yet for 2 reasons 
 Gt4 - workshop ,might not be ready
 
 Gt4 - recent dyno - 170.8 AWKW
 
 it wont have changed much ..
 
 if ti is ready i might see if i can come say hullo - but unlikely ill put her on the rollers at this stage
 |  | 
|  | 
| 
 Location:
 melbourne
 Registered:
 November 2003
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Fri, 26 August 2005 04:28    |  |  |  
	| do u wana setup some basic time brackets for us? 
 what time does it start and what time does it close?
 
 E.G.
 
 FWD cars , 10am - 1pm
 RWD cars, 1pm - 4pm
 AWD cars 4pm - 5pm?
 
 
 |  | 
|  | 
|  
 I Supported Toymods
 
 Location:
 south Melbourne/KL
 Registered:
 June 2004
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Fri, 26 August 2005 06:46    |  |  |  
	| | carsanactra wrote on Fri, 26 August 2005 14:28 |  | do u wana setup some basic time brackets for us?
 
 what time does it start and what time does it close?
 
 E.G.
 
 FWD cars , 10am - 1pm
 RWD cars, 1pm - 4pm
 AWD cars 4pm - 5pm?
 
 
 
 | 
 that would be great but dont think it would work. the last one ppl just showed up randomly
 |  | 
|  | 
| 
 Location:
 melbourne
 Registered:
 November 2003
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Fri, 26 August 2005 07:48    |  |  |  
	| wee in general u know, 
 cause as u say, FWD first, RWD second, AWD last.
 
 can we see how many of each cars there are, an what time does this start. just cause im 4wd so i dont really wana show up at the VERY start of the day and wait hours?
 
 but i will still come early to see what everyone else is pulling
 |  | 
|  | 
|  
 Location:
 Melbourne
 Registered:
 November 2003
 
 |  | 
|  | 
|  
 Location:
 Langwarrin, VIC
 Registered:
 February 2004
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Fri, 26 August 2005 12:46    |  |  |  
	| I'm a reserve?   WOOT! 
 YAYAYYAYA.
 |  | 
|  | 
|  
 I supported Toymods
 
 Location:
 Frankston, Victoria
 Registered:
 April 2004
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Sun, 28 August 2005 01:10    |  |  |  
	| Will try to make it for the next dyno day, don't think i can make it to this one... If I do come I'll probably have no engine in my car so I'll just be there to say hi. 
 Kev.
 |  | 
|  | 
|  
 Location:
 Melbourne
 Registered:
 May 2002
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Sun, 28 August 2005 12:21    |  |  |  
	| only 2 spots for me required |  | 
|  | 
|  
 Location:
 Melbourne
 Registered:
 November 2003
 
 |  | 
|  | 
|  
 Location:
 Ballarat, Victoria
 Registered:
 March 2003
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Mon, 29 August 2005 07:02    |  |  |  
	| so do i need to pay earlier or pay on the day, sorry nim?   |  | 
|  | 
|  
 Location:
 Melbourne
 Registered:
 November 2003
 
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Mon, 29 August 2005 08:29    |  |  |  
	| | Evil_Foetus wrote on Mon, 29 August 2005 17:02 |  | so do i need to pay earlier or pay on the day, sorry nim?
   
 | 
 
 No Deposit! Pay on the day!
 With so many people comming, and so many reserves, it wont matter if a few don't make it, so I don't need to ask for a deposit.
 |  | 
|  | 
|  
 Location:
 Melbourne
 Registered:
 November 2004
 
 | 
	|  Re: Dyno Day - 10th September - Beninca Dyno |  Mon, 29 August 2005 08:40    |  |  |  
	| affirmative |  | 
|  | 
|  
 Location:
 Melbourne
 Registered:
 November 2003
 
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Tue, 30 August 2005 00:30    |  |  |  
	| More dropouts. moo007, Lectric, you're both now confirmed. |  | 
|  | 
|  
 Location:
 South Eastern Subs
 Registered:
 March 2004
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Tue, 30 August 2005 04:47    |  |  |  
	| Name: Boyan Forum: Toymods
 Car: GZ20 Soarer
 Engine: 1G-GTE
 Power: Around 130rwkw
 
 When do you need the deposit by? PM if u like for further details..
 |  | 
|  | 
|  
 I Supported Toymods
 
 Location:
 Lwr Templestowe, Melbourne
 Registered:
 August 2004
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Tue, 30 August 2005 04:57    |  |  |  
	| No need deposit Boyan. Just rock up and pay there 
 
 | Shraka wrote on Mon, 29 August 2005 18:29 |  | 
 | Evil_Foetus wrote on Mon, 29 August 2005 17:02 |  | so do i need to pay earlier or pay on the day, sorry nim?
   
 | 
 
 No Deposit! Pay on the day!
 With so many people comming, and so many reserves, it wont matter if a few don't make it, so I don't need to ask for a deposit.
 
 | 
 
 |  | 
|  | 
|  
 Location:
 Ballarat, Victoria
 Registered:
 March 2003
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Tue, 30 August 2005 05:15    |  |  |  
	| what time on the rocket clock are you getting there yian? 
 
   |  | 
|  | 
|  
 I Supported Toymods
 
 Location:
 Lwr Templestowe, Melbourne
 Registered:
 August 2004
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Tue, 30 August 2005 05:29    |  |  |  
	| Heh... not quite sure. Most probably around 12:30 to 1pm-ish. I'll see if I can make it any earlier. Will let you know. |  | 
|  | 
| 
 Registered:
 August 2005
 
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Tue, 30 August 2005 08:42    |  |  |  
	| | Shraka wrote on Tue, 30 August 2005 10:30 |  | More dropouts. moo007, Lectric, you're both now confirmed.
 
 | 
 
 Woot!! I'm in
   |  | 
|  | 
|  
 I Supported Toymods
 
 Location:
 Lwr Templestowe, Melbourne
 Registered:
 August 2004
 | 
	| Re: Dyno Day - 10th September - Beninca Dyno |  Tue, 30 August 2005 14:23    |  |  |  
	| Hey Nim, 
 1 more from my side. Daniel's bro (TX3 turbo dude).
 
 Name: Elliot
 Forum: None
 Car: R32 Skyline Gtst
 Engine: RB20DET
 Power: ??
 |  | 
|  |