| Author | Topic |
|---|
Location:
Sydney
Registered:
May 2003
|
|
|
I supported Toymods
Location:
Australia
Registered:
November 2003
|
|
Re: MicroTech MT8 For sale
|
Fri, 26 August 2005 01:03
 
|
 |
You might wanna say what its programmed for.
Coz it can't be reprogrammed.
|
|
|
Location:
Sydney
Registered:
May 2003
|
|
Re: MicroTech MTX-8 For sale
|
Fri, 26 August 2005 04:25
|
|
The Microtech MTX-8 can be reprogrammed, if you have noting positive to say please do not say anything on this Post.
Thanks
|
|
|
I supported Toymods
Location:
Australia
Registered:
November 2003
|
|
Re: MicroTech MTX-8 For sale
|
Fri, 26 August 2005 04:27
|
|
Umm, no it can't
Hence me saying that.
Microtech stopped supporting the M series either late last year, or earlier this year.
So unless you know someone that works there, what its programed for now, is locked.
|
|
|
Location:
Sydney
Registered:
May 2003
|
|
Re: MicroTech MTX-8 For sale
|
Fri, 26 August 2005 04:35
|
|
|
It can be reprogrammed for any 4 cylinder. Please do not reply on this post if your not intrested in buying it.
|
|
|
Toymods Social Secretary
Location:
Sydney
Registered:
July 2002
|
|
Re: MicroTech MTX-8 For sale
|
Fri, 26 August 2005 05:27
|
|
i am awaiting a response from Microtech technical support to confirm or deny your claim that the MTX-8 is reconfigurable.
AFAIK, it is NOT reconfigurable, but i will give you the benefit of the doubt until i have it confirmed.
If the MTX-8 is no longer supported, then i request that you list the engine this one is configured for and all other relevant details, else you sale will be deleted.
Regards,
|
|
|
Location:
Canberra
Registered:
November 2004
|
|
Re: MicroTech MTX-8 For sale
|
Fri, 26 August 2005 06:19
|
|
Just a quick question- why is there no loom?
when changing ecu's the loom normaly goes too, cause thats how you buy them.
|
|
|
Location:
Launceston
Registered:
February 2004
|
|
|
Location:
Sydney
Registered:
May 2003
|
|
Re: MicroTech MTX-8 For sale
|
Mon, 29 August 2005 13:05
|
|
Not sure what car it is from as it was giving too me also when i brought the Hand Controller..
It could of been from a Mitsubishi Motor from a Cordia Turbo...
|
|
|
Toymods Social Secretary
Location:
Sydney
Registered:
July 2002
|
|
Re: MicroTech MTX-8 For sale
|
Mon, 29 August 2005 21:44
|
|
Well i have a confirmed email from Microtech saying that ALL M-series ECUs are no longer reconfigurable.
In which case, either list what engine this is for or the sale is deleted.
|
|
|
Location:
Sydney
Registered:
July 2002
|
|
Re: MicroTech MTX-8 For sale
|
Mon, 29 August 2005 22:48
|
|
Microtech used to upgrade MTX-8's to LTX-8's for around $200... its a firmware change and a 232 chip.
They are most likely "not supporting" M series to force you to upgrade.
If you are ringing them up you may as well check out the serial number... no offence but i would be wary of any aftermarket ECU being sold with no loom at all... all microtechs have a serial number that is displayed when you first turn it on with the handset plugged in.
|
|
|
