| Author | Topic |
|---|
Registered:
November 2002
|
|
FS: Fully rebuilt T50 gearbox
|
Thu, 23 January 2003 13:39
|
 |
I have a fully rebuilt T50 gearbox from a TA22 for sale.
All new bearings, gaskets and seals. Asking $250 to someone in Adelaide.
I was going to use it behind my 3T GTE.
Simon
http://users.senet.com.au/~mezz/stitle.htm
|
|
|
Location:
adelaide
Registered:
August 2003
|
 Re: FS: Fully rebuilt T50 gearbox
|
Wed, 13 August 2003 13:34
|
|
dont suppose you still got it in the shed?
|
|
|
Location:
Adelaide
Registered:
May 2003
|
|
Re: FS: Fully rebuilt T50 gearbox
|
Wed, 13 August 2003 23:21
|
|
|
these slip straight into sprinters ey?
|
|
|
I supported Toymods
Location:
Ademelaide, SA
Registered:
July 2003
|
|
Re: FS: Fully rebuilt T50 gearbox
|
Thu, 14 August 2003 08:18
|
|
Still got it?
|
|
|
Location:
qld
Registered:
May 2003
|
|
Re: FS: Fully rebuilt T50 gearbox
|
Thu, 14 August 2003 10:34
|
|
has it go reiciepts etc and does it have a slutch with it.
Jason
|
|
|
I supported Toymods
Location:
Ademelaide, SA
Registered:
July 2003
|
|
Re: FS: Fully rebuilt T50 gearbox
|
Thu, 14 August 2003 10:40
|
|
| truenosedan wrote on Thu, 14 August 2003 08:51 |
these slip straight into sprinters ey?
|
nah...different bellhousing from 't' series, to 'a' series, and different again if you have a 4age....
not much hassle to change a bellhousing though...
|
|
|
Location:
Adelaide
Registered:
May 2003
|
|
Re: FS: Fully rebuilt T50 gearbox
|
Thu, 14 August 2003 13:11
|
|
|
oh ok, how much does the bellhousing swap cost?? is it worth it??
|
|
|
Location:
Eastern Sydney
Registered:
May 2002
|
|
Re: FS: Fully rebuilt T50 gearbox
|
Fri, 15 August 2003 09:39
|
|
there's a lot more to it than the bellhousing. both the input and output shafts are different splines,and the shifter position is different...
the celica box is weaker than the sprinter's,and not a bolt in fit in any sense of the word.
Justin...
|
|
|
I supported Toymods
Location:
Ademelaide, SA
Registered:
July 2003
|
|
Re: FS: Fully rebuilt T50 gearbox
|
Fri, 15 August 2003 13:45
|
|
actually, you're right about the output shaft, but not the input shaft. I once had a KE-30 with a 4a-gze that constantly spat gearboxes, and had two tailshafts to fit the two gearbox types, but I was able to use the same clutch each time....
just wish i coulda found a jap-spec box at the time....
|
|
|
Registered:
November 2002
|
|
Re: FS: Fully rebuilt T50 gearbox
|
Sat, 16 August 2003 03:09
|
|
|
sorry, I sold it a while ago.
|
|
|
