| Author | Topic |
|---|
I supported Toymods
Location:
Sydney
Registered:
May 2002
|
|
TA22 Bits and Pieces for Sales
|
Wed, 29 January 2003 08:12
|
 |
Hey, have the following sale. Same old story, taking up tooo much room. Will be going to the tip if not taken. 
Prices as stated, or make an offer...
Both Front Guards (avg. condition) - FREE
Bootlid - $50
Fuel Tank - $50
Front/Rear Seats (black, avg. condition) - FREE
Rear Bumper - $100
Rear Window - $50
Front Half Exhaust (inc. manifold) - FREE
2T engine (runs) - $150
2T engine (runs on 3 cylinders) - FREE
If there's anything else u may need, it may be lying around.
Reply, pm, etc. if interested.
|
|
|
Location:
Hornsby, Sydney
Registered:
October 2002
|
|
Re: TA22 Bits and Pieces for Sales
|
Wed, 29 January 2003 09:46
|
|
|
can the 2T that runs on 3 cyl still be rebuilt. why does it only run on three?
|
|
|
I supported Toymods
Location:
Sydney
Registered:
May 2002
|
|
Re: TA22 Bits and Pieces for Sales
|
Wed, 29 January 2003 10:43
|
|
|
Don't see why it couldn't be rebuilt. But I am not sure why it runs on 3 cylinders. Was like it when I got it. Was told by previous owner it's "something in the bottom end."
|
|
|
Location:
Newcastle
Registered:
September 2002
|
|
Re: TA22 Bits and Pieces for Sales
|
Thu, 30 January 2003 00:11
|
|
are the front guards the squre edge liped gaurds or the round liped guards?
cheers
tris
|
|
|
Location:
Mornington Peninsula
Registered:
September 2002
|
|
Re: TA22 Bits and Pieces for Sales
|
Thu, 30 January 2003 01:19
|
|
If that engine is running on 3 cylenders and it's not the spark plug or dodgy leads. that usually means something bad has happened, bent valve stems, worn valve seats. Just something for you to look out for. 
I've been there and done that before 
|
|
|
I supported Toymods
Location:
Sydney
Registered:
May 2002
|
|
Re: TA22 Bits and Pieces for Sales
|
Thu, 30 January 2003 07:45
|
|
Yeah. I think it's something bad, but can't be bothered putting it back in a car to find out
It "could" be just the plugs, but not sure.
|
|
|
Location:
Hornsby, Sydney
Registered:
October 2002
|
|
Re: TA22 Bits and Pieces for Sales
|
Fri, 31 January 2003 07:35
|
|
|
it might have a bent valve however that can be rebuilt. the only reason s engines cant be is if a rod has come out the side of the block or simular or if its been bored out to far.
|
|
|
Location:
Brisbane QLD.
Registered:
October 2002
|
|
Re: TA22 Bits and Pieces for Sales
|
Fri, 31 January 2003 08:16
|
|
|
are the front gaurds by any chance of a 77 model
|
|
|
I supported Toymods
Location:
Sydney
Registered:
May 2002
|
|
Re: TA22 Bits and Pieces for Sales
|
Fri, 31 January 2003 12:38
|
|
Nah. Guards are off 75 model.
And no rod's poking out the side. Think it's stock, so not bored out either.
|
|
|
Location:
Canberra
Registered:
October 2002
|
|
Re: TA22 Bits and Pieces for Sales
|
Mon, 03 February 2003 01:41
|
|
|
What sort of condition is the boot lid in?. is it by any chance white?
|
|
|
I supported Toymods
Location:
Sydney
Registered:
May 2002
|
|
Re: TA22 Bits and Pieces for Sales
|
Mon, 03 February 2003 09:20
|
|
|
Boot lid's OK. Has been sanded down though, so has a little bit of surface rust forming..
|
|
|
Location:
Hornsby, N.S.W
Registered:
September 2002
|
|
Re: TA22 Bits and Pieces for Sales
|
Mon, 03 February 2003 12:27
|
|
do you still have any of the windscreen (front and rear) surround chrome, in good condition???
JUZZO
0413461518
|
|
|
I supported Toymods
Location:
Sydney
Registered:
May 2002
|
|
Re: TA22 Bits and Pieces for Sales
|
Tue, 04 February 2003 06:53
|
|
|
Yeah. I have some you could take. They are in OK condition. Need to be cleaned up. Couple of little dents here and there. Let me know if you want to come take a look.
|
|
|
Registered:
October 2002
|
|
|
