Author | Topic |
Location: Sydney
Registered: February 2003
|
|
|
Location: Castle Hill, Sydney
Registered: January 2003
|
|
|
Location: Sydney
Registered: February 2003
|
Re: Ben's Hachi Roku Trueno
|
Mon, 28 April 2003 10:50
|
|
Sorry, don't know how to put attachments on the forum yet.
|
|
|
I supported Toymods Toymods Club Secretary
Location: Sydney
Registered: May 2002
|
Re: Ben's Hachi Roku Trueno
|
Mon, 28 April 2003 11:25
|
|
Awesome!
what sort of engine/suspension setup are you running?
(btw - in your post you have http://http:// at the start of the address for the pictures. get rid of one lot of http:// and they should display fine )
|
|
|
Location: Sydney
Registered: February 2003
|
Re: Ben's Hachi Roku Trueno
|
Mon, 28 April 2003 12:42
|
|
Engine is 4age 20 valve with custom 4-1 extractors, Microtech LTX-8 ECU running 4 coil packs. Suspension is Bilstein race shocks with coil overs, cusco camber tops, Apexi springs up front and Bilstein race shocks, custom springs, JIC adjustable panhard rod at rear. Sway bars are Whiteline front and rear.
|
|
|
Location: sydney
Registered: January 2003
|
Re: Ben's Hachi Roku Trueno
|
Tue, 29 April 2003 06:25
|
|
very nice
so how much did it cost for the trueno front conversion ? where did you get the parts from?
cause i heard there is a kit avaliable in japan to convert levins into truenos for around 1500 or something.
thanks
|
|
|
Location: Sydney
Registered: February 2003
|
Re: Ben's Hachi Roku Trueno
|
Tue, 29 April 2003 06:33
|
|
Its a long story.....I ordered a Trueno front cut from Japan with the stock 16v motor & gearbox. When it arrived they dropped it (flipped upside down) when forklifting from the container. that damaged 1 front light, 1 front guard and distorted the front bar . Then was the drama of ordering new parts which costs a fortune from Japan and too 3 months from a Toyota dealer I know. All up a very expensive exercise and I would nver do it again. Just a bit of costing: from guard cost $580, corner blinkers $95 each.
|
|
|
Location: sydney
Registered: January 2003
|
Re: Ben's Hachi Roku Trueno
|
Tue, 29 April 2003 07:10
|
|
i see, so how much u reckon the trueno front bar, guards, blinkers, flip lights, bonnet basically the whole front would cost for second hand ? 500 ?
|
|
|
Location: Sydney
Registered: February 2003
|
Re: Ben's Hachi Roku Trueno
|
Tue, 29 April 2003 12:28
|
|
Wishful thinking, add a zero to that!
|
|
|
Registered: April 2003
|
Re: Ben's Hachi Roku Trueno
|
Tue, 29 April 2003 13:33
|
|
just wondering,
how u get the sticker on the driver side.
it is exactly same as initial-d.
how you get those FONT?
|
|
|
Location: Sydney
Registered: February 2003
|
Re: Ben's Hachi Roku Trueno
|
Wed, 30 April 2003 13:15
|
|
My sticker guy did it.
|
|
|
Registered: April 2003
|
Re: Ben's Hachi Roku Trueno
|
Wed, 30 April 2003 13:56
|
|
i see..
because the design of the sticker is a bit different from those i saw in HK.
|
|
|
Location: Sydney
Registered: February 2003
|
Re: Ben's Hachi Roku Trueno
|
Thu, 01 May 2003 13:36
|
|
That's because the HK ones are made to suit any car, mine are exact font copy of the Fujiwara Tofu Shop one in Initial D.
|
|
|
I supported Toymods
Location: sydney.au
Registered: August 2002
|
Re: Ben's Hachi Roku Trueno
|
Thu, 29 May 2003 15:38
|
|
not exactly the same ben
i have the orginal (yes the original from shuichi's studio) EPS file that was used in the mangas
if anyone wants it feel free to email me for a copy
|
|
|
Location: Melbourne
Registered: November 2002
|
Re: Ben's Hachi Roku Trueno
|
Sun, 22 June 2003 13:48
|
|
for $500 bux you can't even get a complete aus spec front..
the going rates for all the bits and bobs on a trueno front is about $2000 to $2500 bux...
and you might have to wait a while...
|
|
|
Location: Melbourne
Registered: June 2003
|
Re: Ben's Hachi Roku Trueno
|
Thu, 02 October 2003 14:24
|
|
dood i was wondering if you still have an eps file of the FUJIWARA TOFU SHOP (private vehicle), i just got myself a sign cutting machine and would be very happy to cut you a sign in return!!!
|
|
|
Location: Melbourne
Registered: June 2003
|
Re: Ben's Hachi Roku Trueno
|
Thu, 02 October 2003 14:26
|
|
dood i was wondering if you still have an eps file of the FUJIWARA TOFU SHOP (private vehicle), i just got myself a sign cutting machine or a plotter and would be very happy to cut you a sign in return!!!
|
|
|
Location: perth
Registered: October 2003
|
Re: Ben's Hachi Roku Trueno
|
Tue, 07 October 2003 12:14
|
|
hey, ae86drift, can you send me a copy?
im a initial d fanatic
email: sullia02@tartarus.uwa.edu.au
|
|
|
Location: perth
Registered: October 2003
|
|
|
Location: perth
Registered: October 2003
|
Re: Ben's Hachi Roku Trueno
|
Sat, 11 October 2003 14:20
|
|
so was this originally a oz-spec levin?
|
|
|
Location: Sydney
Registered: February 2003
|
Re: Ben's Hachi Roku Trueno
|
Wed, 29 October 2003 12:03
|
|
Yup, Oz spec sprinter with full Zenki Trueno front guard conversion.
Mods:
-Spot welded body, stripped of sound dead & tar, reprayed black & white panda colour
-Intank SV21 Camry fuel pump conversion.
-Trueno wiring loom, 4age 20 valve conversion, Quads to air
-Port & polished head, shaved, TRD 0.8mm gasket, 11:1 compression
-Microtech LTX-8 ECU, 4 x Bosche coils
-Custom 1.5 inch 4-1 headers, 2.25inch exhaust system, titanium muffler
-Jap T50 gearbox, AE86 flywheel, 4 puck bras button clutch
-MA61 Supra front struts & Brakes with Endless NA-M pads
-Coilover conversion,Bilstein race shocks, 8kg/mm Apexi springs
-Cusco pillow ball camber plates
-Jap AE86 4.3:1 disc brake rear end with TRD 2 way LSD, Endless NA-D pads
-Custom 6.5kg/mm springs rear, JIC alloy panhard rod, Bilstein Race shocks
-Cusco master cylinder stopper
-Front Cusco strut brace, rear KMS strut brace
-Sparco Rev drivers seat, Autotechnica Passenger seat
-Black retrimmed interior, Nardi Classic steering wheel
-C's short shift kit
-Simmons V4 15x7 wheels with shitty Silverstone tyres (good for drift)
-Stickers-Trueno, Apex Twin Cam are all genuine Toyota, Fujiwara was made by a sticker guy
So for its costed me $25,000 and counting and thats parts alone excluding labour costs, lucky I own a workshop! Its done a best of 1.17.7 at Wakefield with the shitty tyres and more mods are coming to get the times down to 1.14's.
Mods coming:
-Toda 3.7kg flywheel
-Toda cambelt, adjustable exhaust camwheel
-Toda 264 inlet & 256 exhaust cams
Mods planning:
-RX7 FC3S 4 pot callipers
-Adjustable lower control arms, caster rods
-RS Watanabe RS8 wheels (gotta look like Takumi)
|
|
|
Location: Sydney
Registered: March 2003
|
Re: Ben's Hachi Roku Trueno
|
Wed, 29 October 2003 12:15
|
|
Hachi Roku Trueno wrote on Wed, 29 October 2003 23:03 | Yup, Oz spec sprinter with full Zenki Trueno front guard conversion.
Mods:
-Spot welded body, stripped of sound dead & tar, reprayed black & white panda colour
-Intank SV21 Camry fuel pump conversion.
-Trueno wiring loom, 4age 20 valve conversion, Quads to air
-Port & polished head, shaved, TRD 0.8mm gasket, 11:1 compression
-Microtech LTX-8 ECU, 4 x Bosche coils
-Custom 1.5 inch 4-1 headers, 2.25inch exhaust system, titanium muffler
-Jap T50 gearbox, AE86 flywheel, 4 puck bras button clutch
-MA61 Supra front struts & Brakes with Endless NA-M pads
-Coilover conversion,Bilstein race shocks, 8kg/mm Apexi springs
-Cusco pillow ball camber plates
-Jap AE86 4.3:1 disc brake rear end with TRD 2 way LSD, Endless NA-D pads
-Custom 6.5kg/mm springs rear, JIC alloy panhard rod, Bilstein Race shocks
-Cusco master cylinder stopper
-Front Cusco strut brace, rear KMS strut brace
-Sparco Rev drivers seat, Autotechnica Passenger seat
-Black retrimmed interior, Nardi Classic steering wheel
-C's short shift kit
-Simmons V4 15x7 wheels with shitty Silverstone tyres (good for drift)
-Stickers-Trueno, Apex Twin Cam are all genuine Toyota, Fujiwara was made by a sticker guy
So for its costed me $25,000 and counting and thats parts alone excluding labour costs, lucky I own a workshop! Its done a best of 1.17.7 at Wakefield with the shitty tyres and more mods are coming to get the times down to 1.14's.
Mods coming:
-Toda 3.7kg flywheel
-Toda cambelt, adjustable exhaust camwheel
-Toda 264 inlet & 256 exhaust cams
Mods planning:
-RX7 FC3S 4 pot callipers
-Adjustable lower control arms, caster rods
-RS Watanabe RS8 wheels (gotta look like Takumi)
|
Hey Ben, sweet list there man!
Around Wakefield what is a respectable time? Say average for a DC2R or S15?
|
|
|
Location: perth
Registered: October 2003
|
Re: Ben's Hachi Roku Trueno
|
Wed, 29 October 2003 13:01
|
|
very nice
real enthusiast huh?
the stickers are genuine toyota? where did you get them from?
|
|
|
Location: Sydney
Registered: February 2003
|
Re: Ben's Hachi Roku Trueno
|
Thu, 30 October 2003 13:43
|
|
Stickers were ordered from Toyota Dealer, They can get them from Japan, Takes weeks and costs a fortune.....around $50 each
Respectable time for DC2Rs are anything under 1.15's. S15's anything under 1.10's. Most S15 are usually around1.13's and DC2Rs about 1.16-1.15.
Ben
|
|
|